98%
921
2 minutes
20
The aim of our study was to examine effects of the length of semen equilibration as well as two freezing techniques on ram sperm post-thaw quality. The ejaculates of Wallachian sheep rams (n = 12) were collected by an electro-ejaculation, equilibrated in a Triladyl® (0, 2, 4, 6, and 8 h) containing glycerol and egg yolk and frozen by programmable freezing (PF) or manual freezing (MF). After thawing, sperm samples were subjected to the motility (computer-assisted sperm analysis [CASA]), viability (SYBR-14/PI), and fertilizing ability (FA) (in vitro penetration/fertilization test on bovine oocytes) assays. It was found that the equilibration of 6 h (E-6) ensured higher post-thaw sperm motility and progressive movement compared with other lengths tested, irrespective of a freezing technique. The E-6 sperm viability did not differ between PF and MF but was lower (P < 0.05) than control. Sperm FA (E-6) was similar in PF (60.44%) and MF (62%) but slightly lower than in fresh (72.8%). Our data demonstrate that the use of MF was comparable with PF, which can be applied in the field conditions without need in a piece of cost-expensive equipment, which can greatly benefit the gene bank of animal genetic resources.
Download full-text PDF |
Source |
---|---|
http://dx.doi.org/10.1111/asj.13670 | DOI Listing |
Proc Natl Acad Sci U S A
September 2025
Department of Bioengineering, Stanford University, Stanford, CA 94305.
Despite periods of permanent darkness and extensive ice coverage in polar environments, photosynthetic ice diatoms display a remarkable capability of living inside the ice matrix. How these organisms navigate such hostile conditions with limited light and extreme cold remains unknown. Using a custom subzero temperature microscope during an Arctic expedition, we present the finding of motility at record-low temperatures in a Eukaryotic cell.
View Article and Find Full Text PDFNanomicro Lett
September 2025
Nanomaterials & System Lab, Major of Mechatronics Engineering, Faculty of Applied Energy System, Jeju National University, Jeju, 63243, Republic of Korea.
Wearable sensors integrated with deep learning techniques have the potential to revolutionize seamless human-machine interfaces for real-time health monitoring, clinical diagnosis, and robotic applications. Nevertheless, it remains a critical challenge to simultaneously achieve desirable mechanical and electrical performance along with biocompatibility, adhesion, self-healing, and environmental robustness with excellent sensing metrics. Herein, we report a multifunctional, anti-freezing, self-adhesive, and self-healable organogel pressure sensor composed of cobalt nanoparticle encapsulated nitrogen-doped carbon nanotubes (CoN CNT) embedded in a polyvinyl alcohol-gelatin (PVA/GLE) matrix.
View Article and Find Full Text PDFJ Sci Food Agric
September 2025
Key Laboratory of Agricultural Product Processing and Storage, Ministry of Agriculture and Rural Affairs, Institute of Food Science and Technology, Chinese Academy of Agricultural Sciences (CAAS), Beijing, China.
Background: Apple pomace (AP), a byproduct of apple processing, is nutrient-rich, and its properties are influenced by both the quality of the apples and the juice extraction process. Drying technology can enhance its economic utilization. This study compared the effects of industrial drum drying (ID) and laboratory hot-air drying, heat pump drying and freeze drying (FD) on the physicochemical, functional and structural properties of from-concentrate AP (FC-AP) and not-from-concentrate AP (NFC-AP).
View Article and Find Full Text PDFACS Appl Mater Interfaces
September 2025
DUT School of Software Technology & DUT-RU International School of Information Science and Engineering, Dalian University of Technology, Dalian 116620, China.
Achieving both high sensitivity and a wide detection range in flexible pressure sensors poses a challenge due to their inherent trade-off. Although porous structures offer promising solutions, conventional methods (templating, foaming, and freeze-drying) fail to precisely control cavity dimensions, spatial arrangement, and 3D morphology, which are crucial for sensing performance. Here, we propose a scalable fabrication strategy that integrates triply periodic minimal surface (TPMS) geometries─precisely engineered via FDM 3D printing─with ultrasonic impregnation of carbon black (CB) into TPU scaffolds.
View Article and Find Full Text PDFMacromol Rapid Commun
September 2025
School of Materials and Chemistry, Anhui Agricultural University, Hefei, Anhui, China.
At present, flexible sensors are a hot spot in research and experimental development, but the research on flexible sensors that can be used for human motion monitoring still needs to be deepened. In this work, the green material cellulose acetate (CA) was used as the matrix material, the film was made by electrospinning, crushed by a cell grinder and sodium alginate (SA) was added to promote the uniform dispersion of nanofibers in water, and then methyltrimethoxysilane (MTMS) and MXene nanosheet dispersion were added to make it hydrophobic and good conductivity, and the aerogel precursor solution was prepared, and then the CA/SA/MTMS/MXene aerogel with directional holes was prepared by directional freeze-drying. As a flexible sensor material, it can be used for human wear, monitoring the electrical signals generated by the movement of human joints and other parts, and can still maintain a current of about 0.
View Article and Find Full Text PDF