98%
921
2 minutes
20
Municipal solid waste (MSW) management practices that lack scientific rigor and use impromptu methods have produced massive leachate in urban complexes. Nowadays, the management of leachate has become an utmost concern worldwide. The MSW landfill site was a low-lying, open dump that operated in a non-engineered way. In this context, the physicochemical characterization of leachate has been carried out. Leachate sampling was done at the Bhandewadi dumpsite, Nagpur, for three seasons (summer, rainy, and winter). During analysis, parameters such as COD, BOD, pH, TKN, TSS, sulfates, and chlorides were analyzed, and the obtained data was compared with the standard EPA 2003 and CPHEEO 2016 methods. Values of COD, BOD, TKN, sulfates, and chlorides were in the range of 2500-16,000 mg/L, 495-2500 mg/L, 167-1900 mg/L, 240-900 mg/L, and 1400-5900 mg/L with respect to all three seasons, respectively. In conjunction with physicochemical analysis, the landfill leachate's leachate pollutant index (LPI) was assessed. The highest LPI values were observed for summer (14.323) as compared to rainy (12.301) and winter (11.348) data. This index reflects the hazardous character of MSW leachate and the total potential for leachate contamination. The results of this study showed seasonal variations in the observed data. Age and seasonal fluctuations therefore substantially influence the composition of the leachate.
Download full-text PDF |
Source |
---|---|
http://dx.doi.org/10.1007/s10661-023-12008-9 | DOI Listing |
J Hazard Mater
September 2025
School of Ecology and Environment, Anhui Normal University, Wuhu, Anhui Province 241002, China; Collaborative Innovation Center of Recovery and Reconstruction of Degraded Ecosystem in Wanjiang Basin Co-Founded by Anhui Province and Ministry of Education, Wuhu, Anhui 241000, China. Electronic address
Tire wear particles (TWP) represent a significant source of marine microplastic pollution and have been shown to pose a considerable threat to marine organisms. In this study, the marine rotifer Brachionus plicatilis was employed as a model organism to systematically assess the effects of micron-sized and nano-sized TWP, as well as their leachates, on rotifer behavior, and underlying molecular mechanisms. The results revealed that TWP exposure significantly reduced rotifer motility, evidenced by decreased swimming speed and acceleration.
View Article and Find Full Text PDFAppl Environ Microbiol
September 2025
College of Life Sciences, Northwest Normal University, Lanzhou, China.
Nitrogen leaching is a major pathway of nitrogen fertilizer loss. Although arbuscular mycorrhizal (AM) fungi are known to reduce nitrogen leaching by improving plant nitrogen uptake, the soil-based mechanisms remain unclear. A pot experiment was conducted using a randomized complete block design, with four nitrogen levels (0, 3.
View Article and Find Full Text PDFWaste Manag
September 2025
Department of Earth and Environment Sciences, St. Francis Xavier University, Antigonish, Canada.
We measured emissions from ten landfills using mobile surveys and Surface Emission Monitoring (SEM) to determine what fraction of emissions can be identified by SEM surveys. SEM is commonly used for regulatory compliance and leak detection at specific locations. However, evolving regulations emphasize the need to manage methane emissions from the entire landfill site, and the suitability of SEM for this objective remains unclear.
View Article and Find Full Text PDFWaste Manag
September 2025
School of Environment, Tsinghua University, Beijing 100084, China. Electronic address:
Effective nitrogen management is critical for minimizing environmental risks in municipal solid waste (MSW) landfills. In-situ aeration has emerged as a practical strategy to accelerate waste stabilization and improve nitrogen stabilization. However, the role of fungi in regulating nitrogen transformation processes-particularly nitrification-remains insufficiently understood.
View Article and Find Full Text PDFJ Mech Behav Biomed Mater
August 2025
Department of Prosthodontics, College of Dentistry, Yonsei University, 50-1 Yonsei-ro, Seodaemun-gu, Seoul, 03722, Republic of Korea. Electronic address:
Photopolymerization-based 3D printing is widely used in dental manufacturing due to its precision and customizability. However, printed resin specimens require effective post-washing to remove unpolymerized resin, which is a critical step that affects both their mechanical properties and biocompatibility. A conventional ultrasonic bath may fail to achieve effective post-washing due to solvent contamination by the residual resin, resulting in incomplete cleaning and possible redeposition.
View Article and Find Full Text PDF