Category Ranking

98%

Total Visits

921

Avg Visit Duration

2 minutes

Citations

20

Article Abstract

We report on the spectral-temporal characterization of a 1.8 μm wavelength and high power picosecond pulse Raman source. It is generated via frequency conversion to the first-order Stokes of a 27 ps chirped pulse Yb-doped fiber laser inside a molecular hydrogen-filled Kagome hollow-core photonic crystal fiber (HC-PCF). Depending on the average power and chirp of the pump laser, the average power of this Raman source can be as high as 9.3 W, and its pulse duration can be as short as ∼17  ps. In agreement with stimulated Raman scattering under the very high gain transient regime, the experimental results show the Stokes spectral structure to change following a three-stage sequence when the average pump power is increased. For a pump with a chirp corresponding to a bandwidth of 200 GHz, we found that for a pump power lower than 7 W, the Stokes spectrum is generated from the blue side of the pump spectrum, and then it exhibits a spectral replica of the pump spectrum for 7-14 W pump power range. Finally,the Stokes spectrum is chiefly generated from the red side of the pump spectrum when the pump power is further increased. Conversely, the Stokes pulse temporal profile shows a strong dependence with the pump power. For a low pump power range, the Stokes pulse exhibits a single peak with a full width at half-maximum of ∼17  ps. For higher pump powers, the Stokes pulse presents a double-peak structure with each peak having a duration of less than 15 ps. The present results can be used to develop compact and efficient frequency down-convertors to the increasingly widespread Yb-based picosecond lasers.

Download full-text PDF

Source
http://dx.doi.org/10.1364/OL.42.003896DOI Listing

Publication Analysis

Top Keywords

pump power
24
pump
12
pump spectrum
12
stokes pulse
12
power
10
high power
8
power raman
8
picosecond pulse
8
raman source
8
average power
8

Similar Publications

Using tunable in-band laser diode (LD) pumping (791.1-798.2 nm), an orthogonally polarized dual-wavelength (OPDW) Nd:LaMgAl11O19/Nd:SrAl12O19 (Nd:LMA/Nd:SA) operation at 1297 nm and 1306 nm for the 4F3/2 → 4I13/2 transition is demonstrated for the first time.

View Article and Find Full Text PDF

Objective: Fontan surgery constructs Total Cavo-Pulmonary Connection Circulation (TCPC), but lacks power. Cavopulmonary circulation assist devices (CPAD) has been proposed to support the Fontan circulation. The virtual implantation of blood pumps into the real TCPC structure to analyze the output characteristics of blood pump and flow pattern can better guide design of the pump and the formulation of powered Fontan surgical protocols.

View Article and Find Full Text PDF

The general theory of oil pumping using gear pumps shows that as kinematic viscosity increases, so does the energy requirement to drive the pump shaft. However, modern oils used in machines and vehicles are characterized by a wide range of modifiers that alter their physical and chemical properties. This article presents a study on the energy demand for driving a gear pump while pumping commercial oils used in machines and vehicles (16 types), such as those for combustion engines in single-drive and hybrid vehicles, gearboxes, hydraulic systems, shock absorbers, chainsaw lubrication, and two-stroke engine fuel mixtures.

View Article and Find Full Text PDF

Background: Postoperative delirium (POD) is a frequent and serious complication in older adults after cardiac surgery. Blood-brain barrier (BBB) dysfunction is implicated in cognitive decline, but its preoperative role in POD remains underexplored. This pilot study aimed to investigate the association between preoperative regional BBB permeability, assessed by dynamic contrast-enhanced magnetic resonance imaging (DCE-MRI), and POD in older patients undergoing off-pump coronary artery bypass grafting (OPCABG).

View Article and Find Full Text PDF

An array of micro-ramp vortex generators (MRVGs) is deployed on the bottom of the ship's hull just before the inlet, aiming to mitigate flow separation on the ramp wall at low inlet velocity ratios (IVR). Four parameters, including height, wedge angle, side length, and spanwise spacing, were analyzed using the numerical methods. Through parametric screening, the optimal height ranges from 20 to 40% of the hull boundary layer thickness upstream of the inlet, while wedge angle and length have negligible effects.

View Article and Find Full Text PDF