98%
921
2 minutes
20
To analyze the factors influencing the time-dependent effect and prognosis of recruitment-to-inflation ratio (R/I) and elastic power in the prone position in patients with moderate-to-severe acute respiratory distress syndrome (ARDS). A prospective, observational cohort study was conducted. A total of 113 patients with moderate-to-severe ARDS were enrolled from December 2022 to October 2024 in the intensive care unit of the First Hospital of Jinzhou Medical University. Patients were divided into survival and death groups based on their 28-day prognosis. Clinical indicators such as R/I, elastic power, mechanical power (MP), oxygenation index (OI), optimal positive end-expiratory pressure (PEEP), respiratory rate (RR), and tidal volume (VT) after 2 hours and 16 hours of prone ventilation treatment between the two groups of patients were compared. Logistic regression was used to analyze the risk factors for 28-day mortality in patients with moderate to severe ARDS treated with prone ventilation. Spearman's correlation method was used to analyze the correlation between R/I and elastic power at various time points during prone ventilation treatment. Receiver operating characteristic (ROC) curve analysis was then used to evaluate the predictive value of R/I and elastic power for the 28-day mortality rate in patients with moderate-to-severe ARDS who were treated with prone ventilation. Compared to the non-survivors, the survival group demonstrated significantly higher R/I, OI, and tidal volume after 2 and 16 hours of prone positioning (all 0.05). Conversely, elastic power, mechanical power, optimal PEEP, and respiratory rate were significantly lower in survivors (all <0.05). Logistic regression analysis revealed that R/I , elastic power , optimal PEEP , and respiratory rate were identified as independent risk factors for predicting 28-day mortality in patients with moderate-to-severe ARDS undergoing prone positioning ventilation (all <0.05). Spearman correlation analysis demonstrated that R/I at 2h and 16h was significantly correlated with elastic power (R values:-0.511 and -0.557, all 0.05). ROC curve analysis showed that the area under the curve (AUC) for R/I was 0.817, whereas the AUC for elastic power was 0.703. The combined AUC for R/I and elastic power was 0.864 (all <0.001). Analysis of the impact of R/I and elastic power on the prognosis of patients with moderate-to-severe ARDS undergoing prone ventilation can be used to assess the lung recruitability within a safe pressure range, as well as the time-dependent response of various factors during the process. This analysis has good predictive value for the 28-day prognosis.
Download full-text PDF |
Source |
---|---|
http://dx.doi.org/10.3760/cma.j.cn112147-20241128-00705 | DOI Listing |
ACS Omega
September 2025
Materials and Manufacturing Directorate, AFRL/RXEE, Air Force Research Laboratory, Wright-Patterson AFB, Ohio 45433, United States.
This study addresses a critical limitation in direct bonded copper (DBC) materials used in power electronics by introducing a copper-zirconium (Cu/Zr) alloy interposing layer at the copper-ceramic interface. This novel design aims to mitigate mechanical stress induced by mismatched material properties, such as the coefficient of thermal expansion (CTE) and elastic modulus, during thermal cycling. The key findings of this study are (1) thermal fatigue improvement: Test samples with the Cu/Zr interface layer (Cu-Cu/Zr-AlN) three times enhanced thermal fatigue resistance, surviving 30 thermal cycles from -55 to 300 °C before delamination, while standard DBC substrates without the Cu/Zr layer failed after just 10 cycles, indicating a performance improvement with the Cu/Zr alloy, (2) durability projections: Based on the Coffin-Manson model, if the upper temperature is capped at 150 °C, the Cu-Cu/Zr-AlN substrates are projected to survive approximately 1372 cycles, underscoring their potential for long-term reliability, and (3) stress mitigation: The Cu/Zr alloy layer bridges the CTE disparity between copper and ceramic, reducing mechanical stress and improving structural integrity across a broad temperature range (-55 to 300 °C).
View Article and Find Full Text PDFBiomater Adv
September 2025
Department of Applied Science and Technology (DISAT), Politecnico di Torino, Corso Duca Degli Abruzzi 24, 10129 Torino, Italy.
Tailoring surface characteristics is key to guiding scaffold interaction with the biological environment, promoting successful biointegration while minimizing immune responses and inflammation. In cardiac tissue engineering, polyvinylidene fluoride (PVDF) is a material of choice for its intrinsic piezoelectric properties, which can be enhanced through electrospinning, also enabling the fabrication of nanofibrous structures mimicking native tissue. However, the inherent hydrophobicity of PVDF can hinder its integration with biological tissues.
View Article and Find Full Text PDFFood Chem
September 2025
Department of Food Engineering and Technology, Sant Longowal Institute of Engineering and Technology, 148106 Longowal, Punjab, India. Electronic address:
Ultrasonication (US) pretreatment (10 and 20 min) before octenyl succinic anhydride (OSA, 3 %) esterification significantly increased the degree of substitution (DS) in proso millet starch, increasing it from 0.0078 to 0.0115.
View Article and Find Full Text PDFSoft Matter
September 2025
Mechanical Engineering Department, Institute of Applied Mathematics School of Biomedical Engineering, University of British Columbia, Vancouver, BC V6T 1Z4, Canada.
Hyperelastic material characterization is crucial for sensing and understanding the behavior of soft materials-such as tissues, rubbers, hydrogels, and polymers-under quasi-static loading before failure. Traditional methods typically rely on uniaxial tensile tests, which require the cumbersome preparation of dumbbell-shaped samples for clamping in a uniaxial testing machine. In contrast, indentation-based methods, which are non-destructive and can be conducted without sample preparation, remain underexplored.
View Article and Find Full Text PDFUltrason Sonochem
August 2025
Guangzhou Women and Children's Medical Center, Guangzhou Medical University, Guangzhou, Guangdong, China; Postdoctoral Workstation of Chongqing General Hospital, Chongqing, China; Department of Ultrasound, Children's Hospital of Chongqing Medical University, National Clinical Research Center for Chi
Ultrasonic cavitation in viscoelastic media is a physical process that features in a variety of chemical reactions, food processing, and biomedical applications due to a range of cavitation-associated physical, chemical, and biological effects. The cavitation effects are essentially caused by the dynamic behaviors of oscillating bubbles, which are strongly influenced by the complex and various inter-bubble interactions. However, how cavitation bubbles interact with each other and these interactions subsequently influence the ultrasonic cavitation dynamics and acoustic emissions in viscoelastic materials still remain poorly understood.
View Article and Find Full Text PDF