Category Ranking

98%

Total Visits

921

Avg Visit Duration

2 minutes

Citations

20

Article Abstract

Aims/hypothesis: Almost all beta cells contact one capillary and insulin granule fusion is targeted to this region. However, there are reports of beta cells contacting more than one capillary. We therefore set out to determine the proportion of beta cells with multiple contacts and the impact of this on cell structure and function.

Methods: We used pancreatic slices in mice and humans to better maintain cell and islet structure than in isolated islets. Cell structure was assayed using immunofluorescence and 3D confocal microscopy. Live-cell two-photon microscopy was used to map granule fusion events in response to glucose stimulation.

Results: We found that 36% and 22% of beta cells in islets from mice and humans, respectively, have separate contact with two capillaries. These contacts establish a distinct form of cell polarity with multiple basal regions. Both capillary contact points are enriched in presynaptic scaffold proteins, and both are a target for insulin granule fusion. Cells with two capillary contact points have a greater capillary contact area and secrete more, with analysis showing that, independent of the number of contact points, increased contact area is correlated with increased granule fusion. Using db/db mice as a model for type 2 diabetes, we observed changes in islet capillary organisation that significantly reduced total islet capillary surface area, and reduced area of capillary contact in single beta cells.

Conclusions/interpretation: Beta cells that contact two capillaries are a significant subpopulation of beta cells within the islet. They have a distinct form of cell polarity and both contact points are specialised for secretion. The larger capillary contact area of cells with two contact points is correlated with increased secretion. In the db/db mouse, changes in capillary structure impact beta cell capillary contact, implying that this is a new factor contributing to disease progression.

Download full-text PDF

Source
http://www.ncbi.nlm.nih.gov/pmc/articles/PMC11343897PMC
http://dx.doi.org/10.1007/s00125-024-06180-xDOI Listing

Publication Analysis

Top Keywords

capillary contact
28
contact points
24
beta cells
24
granule fusion
16
contact
13
capillary
12
cell polarity
12
cells contact
12
contact area
12
beta
9

Similar Publications

Droplet Impact on a Superhydrophobic Surface at Low Weber Numbers.

Langmuir

September 2025

SERB Sponsered Microfluidics Laboratory, Department of Mechanical Engineering, Jadavpur University, Kolkata, West Bengal 700032, India.

This study investigates the dynamic behavior of water droplets impacting a superhydrophobic surface (SHS) at low Weber numbers ( < 17). SHS is fabricated by a chemical coating process on magnesium AZ31 alloy. The surfaces exhibit a Cassie-Baxter wetting state, showing a contact angle of approximately 155°on the surfaces.

View Article and Find Full Text PDF

A novel post-modification strategy was developed for rapid functionalization of monoliths through amino-yne click chemistry. This approach enabled the conjugation of activated alkynes onto amino-functionalized organic-silica hybrid monolith surfaces under mild, catalyst-free conditions. Systematic investigation of critical reaction parameters was conducted to optimize the post-modification process.

View Article and Find Full Text PDF

The emergence of special scenarios involving small-sized penetrating wounds has imposed stricter performance requirements on shape-recovery hemostatic materials, particularly regarding their shape fixity and water-triggered shape recovery efficiency. Herein, an efficient shape-recovery sponge dressing with high shape fixity and high-speed liquid absorption, designated as CQT, was developed by integrating a sieve structure with the rough surface coating. The sieve structure, characterized by microporous structures on macroporous walls, enhanced the multi-level and connectivity of the overall pore network, which could improve compressive fixity via enhancing the energy dissipation required for rebound and enabled efficient shape recovery through augmented capillary action during fluid absorption.

View Article and Find Full Text PDF

Aerogels are widely used in environmental remediation, but their application is hindered by brittleness, limited oil absorption and poor separation of viscous crude oil. In this study, a multifunctional superhydrophobic aerogel with electrothermal and photothermal effects was prepared from bacterial cellulose (BC), methyltrimethoxysilane (MTMS), and hydroxylated carbon nanotubes (HCNT) by soft-hard synergistic and directed freezing. The prepared aerogel exhibited an oriented layered porous structure with excellent compressibility and oil retention capacity.

View Article and Find Full Text PDF

The impact of different surfactants on hydrate formation varies, and exploring hydrate growth characteristics is crucial for advancing the industrial application of oil and gas transportation. This study employed a microscope to investigate the hydrate formation rate and the morphology and formation process of the hydrate along the wall. It also visually demonstrated the hydrate formation process on the wall within an oil-water system and the migration patterns of different liquid phases inside the hydrate, leading to the characteristic of various wall hydrate growth modes.

View Article and Find Full Text PDF