Category Ranking

98%

Total Visits

921

Avg Visit Duration

2 minutes

Citations

20

Article Abstract

The local pH variation near the surface of CO reduction electrodes is important but hard to study. We develop a continuous-flow Raman electrochemical cell that enables the first experimental study of the local pH near a CO reduction gas diffusion electrode under reaction conditions. At zero current, CO chemically reacts with the 1 M KOH electrolyte at the interface to form HCO and CO. The local pH on the cathode surface is 7.2, and the HCO concentration profile extends a distance of 120 μm into the electrolyte, which verifies that the nominal overpotential reduction from using alkaline electrolyte originates from the Nernst potential of the pH gradient layer at the cathode/electrolyte interface. The CO-OH neutralization reaction and the pH gradient layer still persist, albeit to a reduced extent, at CO reduction current densities up to 150 mA/cm.

Download full-text PDF

Source
http://dx.doi.org/10.1021/jacs.0c06779DOI Listing

Publication Analysis

Top Keywords

gas diffusion
8
diffusion electrode
8
reduction alkaline
8
alkaline electrolyte
8
gradient layer
8
reduction
5
situ observation
4
observation gradient
4
gradient gas
4
electrode reduction
4

Similar Publications

Simultaneous removal of NO and propane by solid electrolyte cells with LaPrBaNiO bifunctional electrodes.

J Hazard Mater

September 2025

School of Ecology and Environment, Zhengzhou University, Zhengzhou 450001, China; Henan Key Laboratory of Environmental Chemistry and Low Carbon Technology, Zhengzhou 450001, China. Electronic address:

Solid electrolyte cell is a novel gas purification approach, which has unique superiority in simultaneous nitrogen oxides (NO) and volatile organic compounds (VOCs) removal. The development of effective electrode materials and the comprehensive understanding of reaction mechanisms are essential to advancing this technology. In this study, LaPrBaNiO (x = 0, 0.

View Article and Find Full Text PDF

ZnO dual-functional template-assisted construction of hierarchical porous hard carbon anode for high-rate sodium storage.

J Colloid Interface Sci

September 2025

College of New Energy and Materials, State Key Laboratory of Heavy Oil Processing, China University of Petroleum, Beijing, Changping, 102249, China.. Electronic address:

Hard carbon has emerged as the most widely studied and commercialized anode material for sodium-ion batteries (SIBs). However, improving the charge transfer kinetics within the plateau potential range of the hard carbon anode is crucial for the development of fast-charging SIBs. In this study, we prepared a novel composite material, ZAPA-1300, by uniformly mixing starch, asphalt, and zinc oxide (ZnO), followed by a two-step treatment process.

View Article and Find Full Text PDF

Red blood cell (RBC) size constrains the rate of diffusion of gases between (i) the environment and the capillary beds of the gas exchanger and (ii) the blood and organs. In birds, small RBCs with a high surface area to volume ratio permit a high O diffusion capacity and facilitate sustained, vigorous exercise. Unfortunately, our knowledge of archosaur cardiovascular evolution is incomplete without fossilized RBCs and blood vessels.

View Article and Find Full Text PDF

Giant mobility of surface-trapped ionic charges following liquid tribocharging.

Proc Natl Acad Sci U S A

September 2025

Soft Matter Sciences and Engineering, CNRS, École supérieure de Physique et de Chimie Industrielles de la Ville de Paris, Université Paris Sciences et Lettres, Sorbonne Université, Paris 75005, France.

The sliding motion of aqueous droplets on hydrophobic surfaces leads to charge separation at the trailing edge, with implications from triple-line friction to hydrovoltaic energy generation. Charges deposited on the solid surface have been attributed to ions or electrons ripped off from the liquid drop. However, the dynamics and exact physicochemical nature of these surface-trapped charges remains poorly explored.

View Article and Find Full Text PDF

3D printing, as a versatile additive manufacturing technique, offers high design flexibility, rapid prototyping, minimal material waste, and the capability to fabricate complex, customized geometries. These attributes make it particularly well-suited for low-temperature hydrogen electrochemical conversion devices-specifically, proton exchange membrane fuel cells, proton exchange membrane electrolyzer cells, anion exchange membrane electrolyzer cells, and alkaline electrolyzers-which demand finely structured components such as catalyst layers, gas diffusion layers, electrodes, porous transport layers, and bipolar plates. This review provides a focused and critical summary of the current progress in applying 3D printing technologies to these key components.

View Article and Find Full Text PDF