98%
921
2 minutes
20
Defect-free graphene is impermeable to gases and liquids but highly permeable to thermal protons. Atomic-scale defects such as vacancies, grain boundaries, and Stone-Wales defects are predicted to enhance graphene's proton permeability and may even allow small ions through, whereas larger species such as gas molecules should remain blocked. These expectations have so far remained untested in experiment. Here, we show that atomically thin carbon films with a high density of atomic-scale defects continue blocking all molecular transport, but their proton permeability becomes ∼1000 times higher than that of defect-free graphene. Lithium ions can also permeate through such disordered graphene. The enhanced proton and ion permeability is attributed to a high density of eight-carbon-atom rings. The latter pose approximately twice lower energy barriers for incoming protons compared to that of the six-atom rings of graphene and a relatively low barrier of ∼0.6 eV for Li ions. Our findings suggest that disordered graphene could be of interest as membranes and protective barriers in various Li-ion and hydrogen technologies.
Download full-text PDF |
Source |
---|---|
http://dx.doi.org/10.1021/acsnano.0c02496 | DOI Listing |
Langmuir
August 2025
Centre Européen de Calcul Atomique et Moléculaire (CECAM), École Polytechnique Fédérale de Lasuanne (EPFL), Batochime, Avenue Forel 2, 1015 Lausanne, Switzerland.
Liquid-phase exfoliation via shear flow is a widely adopted technique for the large-scale production of graphene. However, the underlying nano- and microscale exfoliation mechanisms remain poorly understood. In this work, we address this issue by performing hybrid nonequilibrium hydrodynamic simulations of coarse-grained defect-free graphite nanoplatelets immersed in a mesoscopic water fluid via the lattice Boltzmann method.
View Article and Find Full Text PDFNanomaterials (Basel)
July 2025
Department of Mechanical Engineering, TUETECH University, Thai Nguyen 250000, Vietnam.
Point-of-care (POC) diagnostic technologies have become essential for the real-time monitoring and management of chronic wounds, where maintaining a moist environment and controlling pH levels are critical for effective healing. In this study, a flexible pH sensor based on a graphene/molybdenum disulfide (graphene/MoS) composite interdigitated electrode (IDE) structure was fabricated using pulsed laser ablation. The pH sensor, with an active area of 30 mm × 30 mm, exhibited good adhesion to the polyethylene terephthalate (PET) substrate and maintained structural integrity under repeated bending cycles.
View Article and Find Full Text PDFAngew Chem Int Ed Engl
August 2025
Department of Chemistry, Columbia University, New York, New York, 10027, USA.
In this manuscript, we report the first demonstration of controlled helicity in extended graphene nanoribbons (GNRs). We present a wealth of new graphene nanoribbons that are a direct consequence of the high-yielding and robust synthetic method revealed in this study. We created a series of defect-free, ultralong, chiral cove-edged graphene nanoribbons where helical twisting of the graphene nanoribbon backbone is tuned through functionalization with chiral side chains.
View Article and Find Full Text PDFACS Omega
May 2025
Department of Applied Chemistry and Chemical Engineering, Faculty of Engineering and Technology, University of Dhaka, Dhaka 1000, Bangladesh.
The study reports on the development of innovative hierarchical hybrid nanofibers for the efficient removal of cationic heavy metals and dyes from wastewater. The successful electrospinning of poly-(vinyl alcohol) (PVA) and chitosan (CS) in combination with biosynthesized copper oxide nanoparticle-doped graphene oxide nanocomposites (CuO-GO NCs) at various ratios produced functional nanofibers. The CuO-GO NC was synthesized with a facile one-step method.
View Article and Find Full Text PDFACS Appl Mater Interfaces
April 2025
Institute of Superlubricity Technology, Research Institute of Tsinghua University in Shenzhen, Shenzhen 518057, China.
Structural superlubricity (SSL) offers a revolutionary solution to the challenges of friction and wear. However, current transfer methods for superlubric materials rely on probe-based techniques that are limited to individual, one-by-one transfers. Moreover, the maximum achievable scale of SSL is constrained by the single-crystal size and defect distribution of the material.
View Article and Find Full Text PDF