Category Ranking
98%
Total Visits
921
Avg Visit Duration
2 minutes
Citations
20
Article Abstract
Newly prepared titanium alloy (Ti-13Zr-13Nb (TZN)) using powder metallurgy is considered in this investigation. Titanium alloys (TZN) are used in hip and knee replacement for orthopedic implants. Conventional machining, TZN alloys produce higher tool wear rate and poor surface quality, but this can be reduced by Electrical Discharge Machining (EDM) method. Moreover, EDM produce good biological and corrosion resistant surface. In this research, experiments were conducted by considering the influential process factors such as pulse on time, pulse off time, voltage, and current. The experiments were designed based on Response Surface Methodology (RSM) of face centered central composite design. Analysis of Variance (ANOVA) was conducted to identify the significance process factors and their relation to output responses such as Electrode Wear Rate (EWR), Surface Roughness (SR) and Material Removal Rate (MRR). Further, an empirical model was developed by RSM in order to predict the output responses.
Download full-text PDF |
Source |
|---|---|
| http://www.ncbi.nlm.nih.gov/pmc/articles/PMC6369405 | PMC |
| http://dx.doi.org/10.1016/j.dib.2019.01.019 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Nocturnal Oxygen Therapy for Central Sleep Apnea in Patients with Heart Failure: A Multi-site, Double-blind, Sham-controlled Randomized Clinical Trial (LOFT-HF).
Ann Am Thorac Soc
September 2025
Brigham and Women's Hospital, Division of Sleep and Circadian Disorders, Boston, Massachusetts, United States.
Rationale: There are insufficient data to inform the management of central sleep apnea (CSA) in patients with heart failure (HF) with reduced ejection fraction (HFrEF). Nocturnal oxygen therapy (NOT) has been postulated to benefit CSA patients with HFrEF, but has not been rigorously studied. This article is open access and distributed under the terms of the Creative Commons Attribution Non-Commercial No Derivatives License 4.
View Article and Find Full Text PDFAdjuvant potential of metformin with standard anti-seizure medications in persons with active epilepsy: a randomised controlled trial.
Naunyn Schmiedebergs Arch Pharmacol
September 2025
Dept. of Biostatistics, All India Institute of Medical Sciences, New Delhi, India.
The purpose of this study was to investigate the efficacy and safety of add-on metformin treatment in persons with active epilepsy (a-PWE). This is a single-centric, double-blind, placebo-controlled trial randomised a-PWE (1:1) to receive either metformin (extended-release 500 mg) or matching placebo for 6 months along with background antiseizure medications. Primary outcome was percentage change in seizure frequency/month, and secondary outcomes were 50% responder rate, serum mTOR expression, and serum total antioxidant capacity (TAC), body composition analysis, quality of life (QOL), and safety assessment.
View Article and Find Full Text PDFProteomic characterization and lethality of the venom of the Black Judean scorpion, Hottentotta judaicus (Buthidae): expanded toxin diversity and revisited toxicological significance.
Arch Toxicol
September 2025
Laboratorio de Proteómica, Facultad de Microbiología, Instituto Clodomiro Picado, Universidad de Costa Rica, San José, 11501, Costa Rica.
The scorpion Hottentotta judaicus inhabits the Levant region of the Middle East, including Lebanon, Jordan, Palestine, and Israel. While previous research focused on its insecticidal properties and sodium-channel-targeting toxins, its venom remains largely unexplored using modern proteomic approaches. We analyzed the venom composition of H.
View Article and Find Full Text PDFBio-Scaffold Developed With Decellularized Human Amniotic Membrane Composite 3D Umbilical Cord Mesenchymal Stem Cell Spheroids Accelerate the Repair of Rat Defective Wounds.
FASEB J
September 2025
Department of Plastic Surgery and Burn, Third XiangYa Hospital, Central South University, Changsha, Hunan, China.
Defective wounds pose health risks, and treatment is challenging. Umbilical cord-derived mesenchymal stem cells (UCMSCs) show promise for healing. Primary UCMSCs were isolated and extracted in vitro, and the proliferation and differentiation characteristics were detected by flow cytometry and trilineage differentiation, and a 3D spherical cell culture was performed.
View Article and Find Full Text PDFGrayscale Digital Light Processing 3D Printed Microlens for Scale-Down Self-Focusing Printing.
Small
September 2025
Guangdong Provincial Key Laboratory for Processing and Forming of Advanced Metallic Materials, South China University of Technology, Guangzhou, 510640, China.
In modern micro/nano fabrication, 3D printing technology drives industry transformation. However, existing technologies face bottlenecks in improving process efficiency and precision, while also struggling to achieve accurate fabrication of composite 3D microstructures. This study proposes a microlens self-focusing printing technique that integrates digital light processing (DLP) 3D printing with an optical microscope platform.
View Article and Find Full Text PDF