Category Ranking
98%
Total Visits
921
Avg Visit Duration
2 minutes
Citations
20
Article Abstract
All perovskite tandem solar cells (PTSCs) were expected to overcome the Shockley-Queisser limit of single-junction perovskite solar cells (PSCs). Nevertheless, wide bandgap (WBG) subcells suffer from large photovoltage loss and device instability due to extensive film defect, interfacial degradation and phase segregation. Herein, a polymeric multi-dentate anchoring (PMDA) strategy by introducing poly(carbazole phosphonic acid) was employed to engineer the bottom interface and suppress phase segregation. The reinforced and homogeneous anchorage by multiple repeat phosphonic acid groups onto NiO significantly optimised the bottom interface, suppressing unfavourable interfacial reactions and thus alleviating phase segregation of WBG perovskite. As a result, the PMDA-modified WBG PSCs showed higher power conversion efficiency (PCE) than the control device (19.84% vs. 18.18%), along with better device photostability (T = 1200 vs. 500 h). Coupled with narrow bandgap (NBG) PSCs, the PMDA-modified PTSCs reached a PCE of up to 28.51% with device operation photostability over 700 h (T).
Download full-text PDF |
Source |
|---|---|
| http://dx.doi.org/10.1002/anie.202424825 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Effects of CuO Deposition on Cracked TiO Nanoflower Photoanodes in Dye-Sensitized Solar Cells.
Langmuir
September 2025
Microelectronics & Nanotechnology-Shamsuddin Research Centre (MiNT-SRC), Universiti Tun Hussein Onn Malaysia, Batu Pahat 86400 Johor, Malaysia.
Achieving a crack-free, high-surface-area photoanode is essential for maximizing the efficiency of dye-sensitized solar cells (DSSCs). In this work, rutile titanium dioxide (rTiO) nanoflowers were synthesized hydrothermally and then conformally coated with copper(I) oxide (CuO) by RF magnetron sputtering to seal pre-existing cracks and to create a nanothorn surface favorable for dye adsorption. Systematic control of the sputtering time identified 60 min as optimal condition, yielding a photoanode thickness of about 6.
View Article and Find Full Text PDFUltralow-Cost Lacunary Metal-Oxo Framework Enables Efficient and Stable Organic Solar Cells.
Angew Chem Int Ed Engl
September 2025
Department of Material Science & Engineering, City University of Hong Kong, Kowloon, 999077, Hong Kong P.R. China.
Organic solar cells (OSCs) with p-i-n architecture usually exhibit decent efficiency due to the easily tunable energy levels of organic interfacial layers (ILs). However, their operational lifetime is limited by the morphological instability of organic ILs especially the electron-transporting layer (ETL) that shows strong self-aggregation tendency. Besides, organic ETLs are confronted with significant challenges including large batch-to-batch variations and high costs.
View Article and Find Full Text PDFDual-functional phthalamide modulation of aging-resistant PbI for efficient perovskite solar cells.
J Colloid Interface Sci
September 2025
School of Materials Science and Engineering, Taizhou University, Taizhou 318000, China. Electronic address:
The sequential preparation of perovskite solar cells (PSCs) has received widespread concern for its use in large-scale perovskite modules and perovskite/silicon tandem solar cells. However, the instability of the PbI precursor solution and the incomplete reaction of ammonium salts hinder the industrialization of PSCs. Here, by introducing phthalamide (PA) into PbI solution, the carbonyl oxygen of PA molecules undergoes a bidentate coordination reaction with Pb to form an octahedral coordination structure, and the nitrogen atom in the -NH group exhibits weakly acidic properties due to the conjugation effect.
View Article and Find Full Text PDFLife cycle toxicity and reduction potential analysis of perovskite photovoltaic technology.
J Environ Manage
September 2025
Institute of Blue and Green Development, Shandong University, Weihai, 264209, China; Academy of Plateau Science and Sustainability, Qinghai Normal University, Xining, 810016, China. Electronic address:
Perovskite solar cells (PSCs), an emerging photovoltaic technology promising lower cost and higher efficiency, have been developed rapidly. However, the widespread use of lead in current PSCs raises toxicity concerns, prompting interest in lead-free alternatives. Despite this, comprehensive life cycle assessments of toxicity impacts across PSC types remain limited, potentially leading to biased technology choices and environmental harm.
View Article and Find Full Text PDFUnveiling NiO/Perovskite Interfaces: Charge Transport and Device Performance in Perovskite Solar Cells.
ACS Appl Mater Interfaces
September 2025
Advanced Photovoltaics Research Center, Korea Institute of Science and Technology (KIST), Seoul 02792, Republic of Korea.
NiO is a p-type semiconductor widely used as a hole transport material in perovskite solar cells (PSCs), yet the impact of fabrication methods on its interfacial properties and the underlying mechanisms remains unclear. This study investigates how the fabrication process─nanoparticle precursor (NP NiO) and sputtering deposition (SP NiO)─and interfacial space charge effects influence charge transport and device performance in NiO/perovskite systems. SP NiO exhibits a higher Ni/Ni ratio and greater conductivity but induces significant hole depletion and band bending at the interface, leading to reduced open-circuit voltage and efficiency.
View Article and Find Full Text PDF