Category Ranking
98%
Total Visits
921
Avg Visit Duration
2 minutes
Citations
20
Article Abstract
Triboelectric nanogenerators (TENGs) combine contact electrification and electrostatic induction effects to convert waste mechanical energy into electrical energy. As conventional devices contribute to electronic waste, TENGs based on ecofriendly and biocompatible materials have been developed for various energy applications. Owing to the abundance, accessibility, low cost, and biodegradability of biowaste (BW), recycling these materials has gained considerable attention as a green approach for fabricating TENGs. This review provides a detailed overview of BW materials, processing techniques for BW-based TENGs (BW-TENGs), and potential applications of BW-TENGs in emerging bioelectronics. In particular, recent progress in material design, fabrication methods, and biomechanical and environmental energy-harvesting performance is discussed. This review is aimed at promoting the continued development of BW-TENGs and their adoption for sustainable energy-harvesting applications in the field of bioelectronics.
Download full-text PDF |
Source |
|---|---|
| http://www.ncbi.nlm.nih.gov/pmc/articles/PMC11558148 | PMC |
| http://dx.doi.org/10.1002/advs.202405666 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
High-Strength, High-Stability and Multifunctional Sheepskin-Based Organogel e-Skin for the Construction of Multimodal Flexible Sensors and Self-Powered Triboelectric Nanogenerators.
ACS Appl Mater Interfaces
September 2025
Key Laboratory of Leather Chemistry and Engineering of Ministry of Education, Sichuan University, Chengdu 610065, China.
Gel-based electronic skin (e-skin) has recently emerged as one of the most promising interfaces for human-machine interaction and wearable devices, owing to its exceptional flexibility, extensibility, transparency, biocompatibility, high-quality physiological signal monitoring, and system integration suitability. However, conventional hydrogel-based e-skins may exhibit limitations in mechanical strength and stretchability compatibility, as well as poor environmental stability. To address these challenges, following a top-down fabrication strategy, this study innovatively integrates poly(methacrylic acid), titanium sulfate, and ethylene glycol (EG) into the three-dimensional collagen fiber network structure of zeolite-tanned sheepskin to successfully develop an organogel (SMEMT) e-skin, which exhibits superior high toughness, environmental stability, high transparency (74% light transmittance at 550 nm), antibacterial properties and ecological compatibility.
View Article and Find Full Text PDFPorous polysiloxane MWCNT nanocomposites for high-performance and scalable triboelectric nanogenerators.
RSC Adv
August 2025
Institute of Nanoscience and Nanotechnology, National Center for Scientific Research "Demokritos" Agia Paraskevi 15341 Greece.
In this study, porous polysiloxane (PS)/multi-walled carbon nanotube (MWCNT) nanocomposite films were developed as high-performance triboelectric layers for flexible triboelectric nanogenerators (TENGs). TENGs convert mechanical motion into electricity and offer a promising solution for self-powered electronic systems. The nanocomposites were fabricated using a doctor blading method, and porosity was introduced a simple, scalable salt-leaching technique.
View Article and Find Full Text PDFLaser-Induced Photothermal Conversion to Hemispherical MoS Enabling Non-Contact Self-Powering Image Sensor.
Adv Sci (Weinh)
September 2025
Thin Film Materials Research Center, Korea Research Institute of Chemical Technology, Daejeon, 34114, Republic of Korea.
Molybdenum disulfide (MoS) has recently emerged as a promising material for the development of triboelectric nanogenerators (TENGs) owing to its inherently negative triboelectric properties when paired with polymeric layers, along with its notable transparency and mechanical flexibility. However, MoS-based TENGs operating in the contact-separation mode encounter critical limitations, including mechanical wear and limited triboelectric performance, particularly within the constraints of conventional 2D geometries. This paper reports the novel one-step laser-assisted synthesis of hemispherical MoS through the controlled nucleation and growth of MoS precursor seeds.
View Article and Find Full Text PDFEnhancing the output of cellulose-based triboelectric nanogenerators via dual interfacial polarization effects.
Carbohydr Polym
November 2025
Jiangsu Provincial Key Laboratory of Food Advanced Manufacturing Equipment Technology, School of Mechanical Engineering, Jiangnan University, Wuxi 214122, China. Electronic address:
Cellulose-based triboelectric nanogenerators (TENGs) have garnered significant attention in wearable electronics due to their biodegradability and abundant availability. However, the near-electroneutrality of cellulose hinders its advancement and broader application in high-performance TENGs. In this study, the triboelectric polarity of cellulose nanofibers (CNF) is modified by grafting different functional groups, wherein the incorporation of polar sulfonic acid groups enhances the deep trap density on the surface of CNF by an order of magnitude, reduces charge dissipation rates, and increases surface potential by nearly 200 % compared to untreated CNF.
View Article and Find Full Text PDFEnhanced Energy Harvesting and Human-Machine Interaction Sensing via the Tribo-Photovoltaic Effect in a Metal/n-Type GaAs Triboelectric Nanogenerator.
Langmuir
September 2025
Department of Materials Science and Engineering, Indian Institute of Technology Delhi, Hauz Khas, New Delhi 110016, India.
This study presents a novel photovoltaic triboelectric nanogenerator (PTENG) that operates on sliding contacts between n-type (gallium arsenide) GaAs and metal electrodes in the presence of periodic light illumination, which offers harvesting energy synergistically by integrating both photovoltaic and triboelectric effects to enhance the energy output. Using an in-house built test setup with provision of laser illumination, the open-circuit voltage () and short-circuit current () were measured for the n-GaAs semiconductors with different metal contacts (Al and Cu). Under both laser light (630 nm) and without laser light conditions, n-GaAs with aluminum contacts exhibited the highest and values, reaching up to 11.
View Article and Find Full Text PDF