Category Ranking

98%

Total Visits

921

Avg Visit Duration

2 minutes

Citations

20

Article Abstract

Background: This study compared titanium and zirconia implant ligature-induced peri-implant defect progression and response to regenerative surgical intervention.

Methods: Eight tissue-level endosseous implants were placed in 6 mixed-breed foxhounds, with 2 zirconia and 2 titanium alternating in each hemimandible. Cotton ligatures were placed subgingivally for 16 weeks followed by 8 weeks of spontaneous progression. Standardized radiographs were captured every 2 weeks to evaluate the rate of bone loss. Regenerative surgery was performed utilizing water-jet decontamination, enamel matrix derivative, and locally harvested autogenous bone. After 16 weeks of healing, final radiographic bone levels as well as probing depths, recession, and clinical attachment levels were assessed.

Results: All 48 implants integrated successfully. The final average post-ligature radiographic defects were 2.88 and 3.05 mm for titanium and zirconia implants, respectively. There was no significant difference between materials in the rate of radiographic bone loss (p = 0.09). Following regenerative surgery, the total average amount of radiographic bone gain was 1.41 and 1.20 mm for titanium and zirconia, respectively. The percentage of defect fill was 51.56% and 37.98% (p = 0.03) for titanium and zirconia, respectively. Inter-group differences were minimal for clinical parameters at the time of sacrifice including periodontal pocket depths (p = 0.81), recession (p = 0.98), or clinical attachment levels (p = 0.51).

Conclusions: No significant difference was found in the rate of peri-implant defect development between titanium and zirconia implants. Both materials gained significant radiographic bone following regenerative surgery with significantly greater defect percentage fill in titanium implants. The final clinical parameters were similar in both groups.

Download full-text PDF

Source
http://www.ncbi.nlm.nih.gov/pmc/articles/PMC11708443PMC
http://dx.doi.org/10.1002/JPER.23-0573DOI Listing

Publication Analysis

Top Keywords

titanium zirconia
20
radiographic bone
16
regenerative surgery
12
titanium
8
titanium implants
8
peri-implant defect
8
bone loss
8
clinical attachment
8
attachment levels
8
zirconia implants
8

Similar Publications

Purpose: This study aimed to evaluate the inherent and after cyclic loading fracture strength of implant-supported cantilevered fixed prostheses fabricated from recently introduced additively manufactured (AM) and subtractively manufactured (SM) materials, considering variations in prosthesis height.

Materials And Methods: Three cylinder-shaped master files (20 mm long and 11 mm wide) with varying heights (7, 11, and 15 mm) and a titanium-base (Ti-base) abutment space were designed. These designs were used to fabricate a total of 144 specimens with two AM resins indicated for definitive use (Crowntec; AM-CT and Flexcera Smile Ultra+; AM-FS), one high-impact polymer composite (breCAM.

View Article and Find Full Text PDF

Chitosan Bioceramic Composites for Bone Regeneration: Insights from and Studies.

Tissue Eng Part A

September 2025

Department of Anatomy, Faculty of Biomedical Science, University of Otago, Dunedin, New Zealand.

Bone-related pathologies due to injuries, trauma, and disease are a burden on the current health system that will only continue to grow as the population's life expectancy increases. The field of biomaterials aims to address these concerns by exploring, investigating, and optimizing bioregenerative grafts. In the context of bone regeneration, many biomaterials aim to achieve autograft-level regenerative properties, such as osteoconduction, osteoinduction, and low immunogenicity but also aim to address the disadvantages, such as the need for a secondary operation, donor site burden, and limited donor availability.

View Article and Find Full Text PDF

Background: The aim of this study was to investigate the effect of abutment surface treatments (sandblasting and acid or alkali treatments) on the bonding of titanium dental implant abutments and zirconium-supported ceramic crowns with resin-reinforced glass ionomer cement.

Aim: The aim of this research was to determine the optimal surface conditioning method for titanium abutments by comparing the tensile bond strength of resin-reinforced glass ionomer cement after sandblasting, acid etching, and alkali treatment.

Methods: Seventy-six dental implant abutments (AnyOne; MegaGen Co.

View Article and Find Full Text PDF

Purpose: To provide references for the selection of restoration types and materials for the first premolar with large defect in clinical practice.

Methods: A large area defect model of the maxillary first premolar was established and repaired with different types and materials, including group A (inlay group), group B (endocrown group), group C (fiber post core crown group), and group D (pure titanium post core crown group). And then, according to different repair materials, it was divided into 3 subgroups, namely group 1 (zirconia), group 2 (glass ceramic), and group 3 (resin based ceramic), totaling 12 groups.

View Article and Find Full Text PDF

Statement Of Problem: Coated titanium denture attachments have been studied to ensure adequate retention. However, studies on the retentive force of zirconia denture attachment under different implant angulations and insertion-removal cycles are lacking.

Purpose: The purpose of this in vitro study was to evaluate the effect of different implant angulations and insertion-removal cycles on the retentive force of coated titanium and zirconia denture attachments.

View Article and Find Full Text PDF