98%
921
2 minutes
20
Background:: Chronic ankle instability as a prevalent consequence of ankle sprain causes various impairments such as balance and postural control deficits. Foot orthoses are one of the common interventions for rehabilitation of patients with chronic ankle instability.
Objectives:: To investigate the effect of custom-molded foot orthoses with textured surfaces on dynamic balance of chronic ankle instability patients and to compare their effects with other types of foot orthoses.
Study Design:: This is a repeated measure design.
Methods:: A total of 30 participants were recruited based on the guideline introduced by the International Ankle Consortium. The effect of prefabricated, custom-molded, and custom-molded with textured surface foot orthoses was evaluated on dynamic balance by the Star Excursion Balance Test. Normalized reach distances in anteromedial, medial, and posteromedial directions of the test were computed to be used for statistical analysis.
Results:: The foot orthoses increased reach distances compared to the no-orthosis conditions in all three directions. The custom-molded with textured surface foot orthosis has significant differences compared with prefabricated foot orthosis ( p = 0.001) in all measured directions and with custom-molded foot orthosis ( p < 0.01) in medial and posteromedial directions.
Conclusion:: Foot orthoses improve reach distances in patients with chronic ankle instability. Custom-molded with textured surface foot orthosis has a more pronounced effect compared with other foot orthoses.
Clinical Relevance: The custom-molded foot orthosis with textured surface could be an effective device to improve dynamic balance in chronic ankle instability (CAI) patients. It may be considered as an efficient intervention to reduce ankle sprain recurrence in these individuals, although further research should be conducted.
Download full-text PDF |
Source |
---|---|
http://dx.doi.org/10.1177/0309364618792718 | DOI Listing |
PLoS One
September 2025
Institute of Biomedical Engineering, University of Toronto, Toronto, Ontario, Canada.
Achieving optimal alignment and fit is a key aspect of ankle-foot orthosis (AFO) design, as it directly influences the effectiveness of the device. While digital workflows offer the potential to integrate quantifiable alignment measures and corrections into AFO design, a major challenge remains in controlling lower-limb positioning and alignment during 3D scanning. This study aimed to evaluate pediatric AFO alignment and shape differences of directly scanned (live scan) vs casted lower limb models.
View Article and Find Full Text PDFMed Eng Phys
October 2025
Centre for Biomechanics and Rehabilitation Technologies, Staffordshire University, Stoke-On-Trent, UK; Reading Central PCN, Reading, UK.
Background: Drape-forming is a cost-effective method used worldwide to manufacture bespoke ankle foot orthoses (AFOs). It involves draping a heated polymer material sheet over a positive cast of the user's limb. Previous research has shown that the manual nature of drape-forming can influence the thickness of the final AFO and even lead to structures that are inadequately rigid to be clinically effective.
View Article and Find Full Text PDFJ Cosmet Dermatol
September 2025
Department of Practical Cosmetology and Skin Diagnostics, Faculty of Pharmaceutical Sciences in Sosnowiec, Medical University of Silesia, Katowice, Poland.
Background: Ingrown toenails are a disease that often begins in childhood. It occurs as the penetration of the nail plate into the surrounding tissue as a result of various factors. Patients often report to various specialists, including podiatrists and dermatologists, at an advanced stage of this disease.
View Article and Find Full Text PDFBMC Musculoskelet Disord
September 2025
Department of Biotechnology and Life Sciences, University of Insubria, Varese, Italy.
Introduction: 3D-printing is an emerging technology that is used in the manufacturing of orthotic devices. 3D-printing has many advantages such as improved fit, comfort, effectiveness, and patient satisfaction. While some challenges like durability and material selection remain, the aim of this systematic review is to provide a comprehensive evaluation of the clinical outcomes of 3D-printed orthoses.
View Article and Find Full Text PDFLife (Basel)
August 2025
Precision Medicine in the Medical, Surgical and Critical Care Areas, University of Palermo, 90100 Palermo, Italy.
Haemophilic arthropathy is caused by repeated joint bleeding episodes, primarily affecting knees, ankles and elbows. Conservative options should be considered prior to surgery, as well as postural evaluation, since any functional overload promotes the development of new bleeding. The aim of this study is to verify the use of foot orthoses in combination with postural rehabilitation, assessing the incidence of spontaneous haemarthroses and haematomas.
View Article and Find Full Text PDF