Category Ranking
98%
Total Visits
921
Avg Visit Duration
2 minutes
Citations
20
Article Abstract
The conventional analytical HPLC was successfully developed for micro-column separation by using a simple eluate splitting system, a self-preparation of monolithic column and an on-capillary column detector in our laboratory. A typical polystyrene-based monolith was quickly prepared inside the fused-silica capillary, which in situ polymerization was carried out in 10 min by microwave irradiation. The reactant solution consisted of styrene (ST) as a functional monomer, divinylbenzene (DVB) as a cross-linking agent, toluene and isooctane as porogenic solvents, and azobisisobutyronitrile (AIBN) as an initiator. The monolith was proved to form in the center of the capillary and adhered to the column inner wall by the scanning electron micrograph. Its chromatographic behaviors were evaluated in detail by varying the flow rate and percentage of mobile phases, and under the optimal condition, baseline separation of the model analytes including thiourea, benzene, toluene, ethylbenzene was obtained with a highest theoretical plate number near 11,290 N/m by the developed capillary HPLC. Furthermore, the stability and porosity of the prepared monolith were systematically investigated by a simple flow method.
Download full-text PDF |
Source |
|---|---|
| http://dx.doi.org/10.1007/s00216-009-2708-x | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Sulfonated polyHIPE/nanoclay composites with hierarchically porous structure for efficient removal of endocrine-disrupting hormone from aqueous solution.
Water Environ Res
May 2023
Department of Polymer Materials Engineering, Faculty of Engineering, Yalova University, Yalova, Turkey.
The objective of this study is the synthesis of macroporous polystyrene-based polyHIPE/nanoclay (p[HIPE]/NClay) monoliths and post-functionalization of the monoliths through sulfonation to improve the structural and textural properties as well as adsorption performances toward bisphenol A (BPA) as an endocrine-disrupting chemical. The adsorption tests were conducted with raw p(HIPE), nanoclay, p(HIPE)/NClay, and sulfonated samples in order to obtain insights in the adsorption mechanism. The synergy between clay embedding and sulfonation resulted in higher BPA removal performance of p(HIPE)/NClay@S sample (96% removal) when compared with the raw polyHIPE (52% removal).
View Article and Find Full Text PDFFacile Fabrication of Superhydrophobic Graphene/Polystyrene Foams for Efficient and Continuous Separation of Immiscible and Emulsified Oil/Water Mixtures.
Polymers (Basel)
June 2022
School of Engineering, Southwest Petroleum University, Nanchong 637001, China.
Three-dimensional superhydrophobic/superlipophilic porous materials have attracted widespread attention for use in the separation of oil/water mixtures. However, a simple strategy to prepare superhydrophobic porous materials capable of efficient and continuous separation of immiscible and emulsified oil/water mixtures has not yet been realized. Herein, a superhydrophobic graphene/polystyrene composite material with a micro-nanopore structure was prepared by a single-step reaction through high internal phase emulsion polymerization.
View Article and Find Full Text PDFFabrication of polymer monoliths within the confines of non-transparent 3D-printed polymer housings.
J Chromatogr A
July 2020
Van't Hoff Institute for Molecular Sciences, Science Park, University of Amsterdam 1098 HX Amsterdam, Netherlands; The Centre for Analytical Sciences Amsterdam (CASA), University of Amsterdam 1098 HX Amsterdam, Netherlands.
In the last decade, 3D-printing has emerged as a promising enabling technology in the field of analytical chemistry. Fused-deposition modelling (FDM) is a popular, low-cost and widely accessible technique. In this study, RPLC separations are achieved by in-situ fabrication of porous polymer monoliths, directly within the 3D-printed channels.
View Article and Find Full Text PDFSemi-micro reversed-phase liquid chromatography for the separation of alkyl benzenes and proteins exploiting methacrylate- and polystyrene-based monolithic columns.
J Sep Sci
May 2016
Departamento de Química Fundamental, Instituto de Química, Universidade de São Paulo, São Paulo, SP, Brazil.
Monolithic columns were synthesized inside 1.02 mm internal diameter fused-silica lined stainless-steel tubing. Styrene and butyl, hexyl, lauryl, and glycidyl methacrylates were the functional monomers.
View Article and Find Full Text PDFEvaluation of interactions between metal ions and nonionic surfactants in high-concentration HCl using low-pressure high-performance liquid chromatography with low-flow-resistance polystyrene-based monolithic column.
Anal Bioanal Chem
October 2013
Department of Materials Science and Engineering, Graduate School of Engineering, Nagoya Institute of Technology, Gokiso, Showa, Nagoya, 466-8555, Japan.
A method for evaluating the interactions between metal ions and nonionic surfactants in aqueous solutions containing high-concentration HCl, using gas pressure-driven low-pressure high-performance liquid chromatography (LP-HPLC) as a highly acid-resistant HPLC system, was developed. To construct the LP-HPLC for this purpose, poly(styrene-co-divinylbenzene)-based low-flow-resistance monolithic columns tolerant to highly acidic conditions were prepared using low-conversion thermal polymerization. Thermal polymerization at 65 °C for 1.
View Article and Find Full Text PDF