Polymethylmethacrylate particles inhibit osteoblastic differentiation of MC3T3-E1 osteoprogenitor cells.

J Orthop Res

Department of Orthopaedic Surgery, Stanford University Medical Center, 300 Pasteur Drive, Edwards Building, R-116, Stanford, California 94305-5341, USA.

Published: July 2008


Category Ranking

98%

Total Visits

921

Avg Visit Duration

2 minutes

Citations

20

Article Abstract

Orthopedic wear debris has been implicated as a significant inhibitory factor of osteoblast differentiation. Polymethylmethacrylate (PMMA) particles have been previously shown to inhibit the differentiation of osteoprogenitors in heterogeneous murine marrow stromal cell cultures, but the effect of PMMA particles on pure osteoprogenitor populations remains unknown. In this study, we challenged murine MC3T3-E1 osteoprogenitor cells with PMMA particles during their initial differentiation in osteogenic medium. MC3T3-E1 cultures challenged with PMMA particles showed a gradual dose-dependent decrease in mineralization, cell number, and alkaline phosphatase activity at low particle doses (0.038-0.150% v/v) and complete reduction of these outcome parameters at high particle doses (> or =0.300% v/v). MC3T3-E1 cultures challenged with a high particle dose (0.300% v/v) showed no rise in these outcome parameters over time, whereas cultures challenged with a low particle dose (0.075% v/v) showed a normal or reduced rate of increase compared to controls. Osteocalcin production was not significantly affected by particles at all doses tested. MC3T3-E1 cells grown in conditioned medium from particle-treated MC3T3-E1 cultures showed a significant reduction in mineralization only. These results indicate that direct exposure of MC3T3-E1 osteoprogenitors to PMMA particles results in suppression of osteogenic proliferation and differentiation.

Download full-text PDF

Source
http://dx.doi.org/10.1002/jor.20618DOI Listing

Publication Analysis

Top Keywords

pmma particles
20
mc3t3-e1 cultures
12
cultures challenged
12
particles inhibit
8
mc3t3-e1 osteoprogenitor
8
osteoprogenitor cells
8
low particle
8
particle doses
8
outcome parameters
8
high particle
8

Similar Publications

Background: As advanced treatment plans increasingly include optimizing both dose and linear energy transfer (LET), there is a growing demand for tools to measure LET in clinical settings. Although various detection systems have been investigated in this pursuit, the scarcity of detectors capable of providing per-ion data for a fast and streamlined verification of LET distributions remains an issue. Silicon pixel detector technology bridges this gap by enabling rapid tracking of single-ion energy deposition.

View Article and Find Full Text PDF

This study investigates the application of triboelectric separation technology for the efficient recovery of glass fibre-reinforced polymers (GFRPs) from wind turbine blade. Through systematic experiments, the effects of friction materials, electrode voltage and feed rate on separation efficiency were evaluated. The results demonstrate that using polymethyl methacrylate as the friction material, with an electrode voltage of 12.

View Article and Find Full Text PDF

Polymethylmethacrylate (PMMA) is the most used bone cement in orthopaedic surgery for the fixation of prosthetic components or filling bone defects. PMMA bone cements containing magnetic particles have been explored for the treatment of bone cancers using magnetic induction hyperthermia. In this study, different formulations of magnetic bone cements were developed by mixing up to 40 wt% of magnetic glass-ceramics with Palacos MV, a commercial PMMA bone cement with medium viscosity.

View Article and Find Full Text PDF

Background: Acrylic resins are extensively used in prosthodontics, orthodontics and maxillofacial prosthetics due to their ease of fabrication and cost-effectiveness. However, conventional acrylic materials are susceptible to microbial colonization, mechanical deterioration and esthetic compromise. To overcome these limitations, recent research has explored the incorporation of nanoparticles into polymethyl methacrylate (PMMA)-based resins to enhance their antimicrobial efficacy, mechanical strength, biocompatibility, and long-term durability.

View Article and Find Full Text PDF

Molecular interaction with micro- and nano-plastics (MNPs) is an important chemical process that dictates the fate and transport of organic contaminants, and that of MNPs, within the aquatic environment. In this study, adsorption of cationic, anionic, and neutrally charged organic molecules from aqueous solution to model microplastics (MPs) is presented. Second harmonic generation, an interfacial selective laser-based technique that allows measurements of adsorption isotherms, has been used.

View Article and Find Full Text PDF