Structural and spatially resolved studies on the hardening of a commercial resin-modified glass-ionomer cement.

J Mater Sci Mater Med

Departamento de Engenharia de Materiais, Instituto Superior Técnico, Universidade Técnica de Lisboa, Lisboa, Portugal.

Published: May 2007


Category Ranking

98%

Total Visits

921

Avg Visit Duration

2 minutes

Citations

20

Article Abstract

A commercial photopolymerizable resin-modified glass-ionomer (Fuji II LC) was studied using a variety of nuclear magnetic resonance (NMR) techniques. (1)H and (19)F stray-field imaging (STRAFI) enabled to follow the acid-base reaction kinetics in self-cured (SC) samples. Gelation and maturation processes with 25 min and 40 h average time constants, respectively, were distinguished. In self- & photo-cured (SPC) samples, two processes were also observed, which occurred with 2 s and 47 s average time constants. (1)H, (27)Al and (29)Si magic angle spinning (MAS) NMR, (13)C cross-polarization (CP)/MAS NMR and (27)Al multiple quanta (MQ)MAS NMR spectroscopy were used to obtain structural information on the glass and cements that were either SC or SPC. The presence of methacrylate groups was identified in the solid component. Unreacted hydroxyl ethylmethacrylate (HEMA) was detected in self-cured cement. (27)Al data showed that approximately 28% and 20% of Al is leached out from glass particles in SC and SPC samples, respectively. The upfield shift detected in (29)Si MAS NMR spectra of the cements is consistent with a decrease in the number of Al species in the second coordination sphere of the silicon structures. Scanning electron microscopy (SEM) showed existence of 3D shrinkage of the cement matrix in photo-cured cements.

Download full-text PDF

Source
http://dx.doi.org/10.1007/s10856-006-0010-4DOI Listing

Publication Analysis

Top Keywords

resin-modified glass-ionomer
8
average time
8
time constants
8
spc samples
8
mas nmr
8
nmr
5
structural spatially
4
spatially resolved
4
resolved studies
4
studies hardening
4

Similar Publications

Objective: To assess the cost-effectiveness of silver diamine fluoride (SDF) relative to sodium fluoride (NaF) and traditional resin-modified glass ionomer cements (RMGIC) restorations for the management of root caries in older adults aged 60 and above.

Methods: A Markov model design was chosen and two models were constructed: 1) Clinic-based model - with access to dental facility that allows for placement of traditional restorations, 2) Community-based model - without access to dental facility due to mobility, lack of executive function, or financial barriers. Modelling was done over a 10-year time horizon with a cycle length of one year.

View Article and Find Full Text PDF

Biomimetic restorative treatments in pediatric dentistry increase the longevity of the restoration compared to traditional methods and aim to preserve the natural tooth structure. Prefabricated zirconia crowns have been developed as aesthetic alternatives to stainless steel crowns for full-coronal restorations of primary teeth. This study aimed to compare the fracture resistance and microleakage of two different posterior zirconia crown brands-NuSmile (USA) and ProfZrCrown (Turkey)-cemented with either conventional glass ionomer cement (GIC) or resin-modified glass ionomer cement (RMGIC).

View Article and Find Full Text PDF

To evaluate the influence of commonly used restorative materials, including zinc oxide eugenol (ZOE), resin-modified glass ionomer cement (RMGIC) and stainless steel crowns (SSC), on the setting reaction (measured by microhardness) of Endo-Cem Premix Mineral Trioxide Aggregate (PMTA) when used as a pulpotomy agent. Fifty extracted primary molars had a pulpotomy with a three-millimeter layer of EndoCem PMTA applied to the pulpal floor. Specimens were divided into five groups: group one (control), EndoCem with a moistened cotton pellet; group two, EndoCem with RMGIC; group three, EndoCem with ZOE; group four, EndoCem with RMGIC and SSC; and group five, EndoCem with ZOE and SSC.

View Article and Find Full Text PDF

Reimagining bonding interfaces: UV photofunctionalization, a novel physicochemical approach, unlocks titanium and cement adhesive potential.

Dent Mater

August 2025

Weintraub Center for Reconstructive Biotechnology, UCLA School of Dentistry, Los Angeles, CA 10833, USA; Division of Regenerative and Reconstructive Sciences, UCLA School of Dentistry, Los Angeles, CA 10833, USA. Electronic address:

Objectives: Mechanical roughening and chemical priming are conventional techniques to improve material bonding, but they come with inherent limitations. This study aimed to investigate a novel physicochemical approach-UV photofunctionalization-to enhance bonding performance between titanium and glass ionomer cement.

Methods: Shear bond strength tests were conducted using Grade 4 commercially pure titanium and a resin-modified glass ionomer cement.

View Article and Find Full Text PDF

Evaluation of Microleakage and Micromorphological Analysis of Different Self-Adhesive Restorative Systems in Class V Cavities: Laboratory Study.

J Clin Exp Dent

July 2025

Professor, BDS, MDS, PhD, Department of Conservative Dentistry, Faculty of Dentistry, Mansoura University, Mansoura, Egypt, Algomhoria Street, Mansoura, Aldakhlia, Egypt P.O.

Background: Microleakage is a common problem that affects the longevity of restorative materials in Class V cavities. It is influenced by factors such as the type of restorative materials, composition of the cavity margins and aging. This study aimed to evaluate and compare microleakage and micromorphological analysis of restoration-dentin interface for Class V cavities restored with resin modified glass ionomer cement, self-adhesive flowable composite and self-adhesive composite hybrid before and after thermocycling for 10000 cycles.

View Article and Find Full Text PDF