The Influence of UV-Ozone, O Plasma, and CF Plasma Treatment on the Droplet-Based Deposition of Diamond Nanoparticles.

Surface treatment is critical for homogeneous coating over a large area and high-resolution patterning of nanodiamond (ND) particles. To optimize the interaction between the surface of a substrate and the colloid of ND particles, it is essential to remove hydrocarbon contamination by surface treatment and to increase the surface energy of the substrate, hence improving the diamond film homogeneity upon its deposition. However, the impact of substrate surface treatment on the properties of coatings and patterns is not fully understood.

Electron-donating amine-interlayer induced n-type doping of polymer:nonfullerene blends for efficient narrowband near-infrared photo-detection.

Inherently narrowband near-infrared organic photodetectors are highly desired for many applications, including biological imaging and surveillance. However, they suffer from a low photon-to-charge conversion efficiencies and utilize spectral narrowing techniques which strongly rely on the used material or on a nano-photonic device architecture. Here, we demonstrate a general and facile approach towards wavelength-selective near-infrared phtotodetection through intentionally n-doping 500-600 nm-thick nonfullerene blends.

Inkjet Printing of PEDOT:PSS Based Conductive Patterns for 3D Forming Applications.

This paper presents the formulation, inkjet printing, and vacuum forming of a conductive and stretchable polymer, poly(3,4-ethylenedioxythiophene) polystyrene sulfonate (PEDOT:PSS), ink on a stretchable and transparent thermoplastic polyurethane (TPU) substrate. The formulation of the conductive and stretchable ink is achieved by combining PEDOT:PSS with additional solvents, to achieve the right inkjet properties for drop-on-demand (DoD) inkjet printing. A conductive pattern can be printed from the 21 µm orifice on a flexible and stretchable TPU substrate, with a linewidth down to 44 µm.

Improved Field Electron Emission Properties of Phosphorus and Nitrogen Co-Doped Nanocrystalline Diamond Films.

Nanocrystalline diamond (NCD) field emitters have attracted significant interest for vacuum microelectronics applications. This work presents an approach to enhance the field electron emission (FEE) properties of NCD films by co-doping phosphorus (P) and nitrogen (N) using microwave plasma-enhanced chemical vapor deposition. While the methane (CH) and P concentrations are kept constant, the N concentration is varied from 0.

Laser-Patternable Graphene Field Emitters for Plasma Displays.

This paper presents a plasma display device (PDD) based on laser-induced graphene nanoribbons (LIGNs), which were directly fabricated on polyimide sheets. Superior field electron emission (FEE) characteristics, viz. a low turn-on field of 0.

Steering the Properties of MoOx Hole Transporting Layers in OPVs and OLEDs: Interface Morphology vs. Electronic Structure.

The identification, fine-tuning, and process optimization of appropriate hole transporting layers (HTLs) for organic solar cells is indispensable for the production of efficient and sustainable functional devices. In this study, the optimization of a solution-processed molybdenum oxide (MoOx) layer fabricated from a combustion precursor is carried out via the introduction of zirconium and tin additives. The evaluation of the output characteristics of both organic photovoltaic (OPV) and organic light emitting diode (OLED) devices demonstrates the beneficial influence upon the addition of the Zr and Sn ions compared to the generic MoOx precursor.

Band Gap Tuning via Lattice Contraction and Octahedral Tilting in Perovskite Materials for Photovoltaics.

Tin and lead iodide perovskite semiconductors of the composition AMX, where M is a metal and X is a halide, are leading candidates for high efficiency low cost tandem photovoltaics, in part because they have band gaps that can be tuned over a wide range by compositional substitution. We experimentally identify two competing mechanisms through which the A-site cation influences the band gap of 3D metal halide perovskites. Using a smaller A-site cation can distort the perovskite lattice in two distinct ways: by tilting the MX octahedra or by simply contracting the lattice isotropically.

Reversible restructuring of supported Au nanoparticles during butadiene hydrogenation revealed by operando GISAXS/GIWAXS.

Periodically arranged, monodisperse gold nanoparticles supported on flat silicon substrates were studied for the hydrogenation of 1,3-butadiene under operando conditions using Grazing Incidence Small- and Wide-Angle X-ray Scattering (GISAXS/GIWAXS). It was found that the composition and shape of the nanoparticles depends very much on the chemical environment; the particles are shown to be dynamic, undergoing reversible size and shape change particularly during catalytic reaction, highlighting a dynamism often not observed in traditional studies. Specifically, the size of the Au nanoparticles increases during butadiene hydrogenation and this is attributed to the partial removal of a AuO at the metal-oxide interface and consequential shape change of the nanoparticle from a more hemispherical particle to a particle with a larger height to width ratio.

Structure-Property Relations of Methylamine Vapor Treated Hybrid Perovskite CHNHPbI Films and Solar Cells.

The power conversion efficiency of halide perovskite solar cells is heavily dependent on the perovskite layer being sufficiently smooth and pinhole-free. It has been shown that these features can be obtained even when starting out from rough and discontinuous perovskite film by briefly exposing the film to methylamine (MA) vapor. The exact underlying physical mechanisms of this phenomenon are, however, still unclear.

Perovskite-perovskite tandem photovoltaics with optimized band gaps.

We demonstrate four- and two-terminal perovskite-perovskite tandem solar cells with ideally matched band gaps. We develop an infrared-absorbing 1.2-electron volt band-gap perovskite, FACsSnPbI, that can deliver 14.

A Universal Deposition Protocol for Planar Heterojunction Solar Cells with High Efficiency Based on Hybrid Lead Halide Perovskite Families.

A robust and expedient gas quenching method is developed for the solution deposition of hybrid perovskite thin films. The method offers a reliable standard practice for the fabrication of a non-exhaustive variety of perovskites exhibiting excellent film morphology and commensurate high performance in both regular and inverted structured solar cell architectures.

Assessing the toxicity of Pb- and Sn-based perovskite solar cells in model organism Danio rerio.

Intensive development of organometal halide perovskite solar cells has lead to a dramatic surge in power conversion efficiency up to 20%. Unfortunately, the most efficient perovskite solar cells all contain lead (Pb), which is an unsettling flaw that leads to severe environmental concerns and is therefore a stumbling block envisioning their large-scale application. Aiming for the retention of favorable electro-optical properties, tin (Sn) has been considered the most likely substitute.

Segregation versus colocalization: orthogonally functionalized binary micropatterned substrates regulate the molecular distribution in focal adhesions.

Orthogonally functionalized binary micropatterned substrates are produced using a novel protocol. The use of adequate peptido-mimetics enables an unprecedented segregation of purified αvβ3 and α5β1 integrins in adjacent microislands and evidences the preference of U2OS cells to colocalize such receptors. Moreover, this tendency can be altered by varying the geometry and composition of the micropatterns.

Nafion-modified MoOx as effective room-temperature hole injection layer for stable, high-performance inverted organic solar cells.

We present a hole injection layer processed from solution at room temperature for inverted organic solar cells. Bis(2,4-pentanedionato) molybdenum(VI) dioxide (MoO2(acac)2) is used as the precursor for MoOx. Small amounts of Nafion in the precursor solution allow it to form continuous films with good wetting onto the active layers.

Organic phototransistors using poly(3-hexylthiophene) nanofibres.

Here we report the fabrication of nanofibre-based organic phototransistors (OPTs) using preformed poly(3-hexylthiophene) (P3HT) nanofibres. OPT performance is analysed based on two important parameters: photoresponsivity R and photosensitivity P. Before testing the devices as OPTs, the normal organic field-effect transistor (OFET) operation is characterized, revealing a surface-coverage-dependent performance.

Ultrathin ammonium heptamolybdate films as efficient room-temperature hole transport layers for organic solar cells.

Ammonium heptamolybdate (NH4)6Mo7O24·4H2O (AHM) and its peroxo derivatives are analyzed as solution-processed room temperature hole transport layer (HTL) in organic solar cells. Such AHM based HTLs are investigated in devices with three different types of active layers, i.e.

Perovskite-based hybrid solar cells exceeding 10% efficiency with high reproducibility using a thin film sandwich approach.

Organometal halide perovskites have tremendous potential as light absorbers for photovoltaic applications. In this work we demonstrate hybrid solar cells based on the mixed perovskite CH3 NH3 PbI2 Cl in a thin film sandwich structure, with unprecedented reproducibility and generating efficiencies up to 10.8%.

Selective protein immobilization onto gold nanoparticles deposited under vacuum on a protein-repellent self-assembled monolayer.

The immobilization of proteins on flat substrates plays an important role for a wide spectrum of applications in the fields of biology, medicine, and biochemistry, among others. An essential prerequisite for the use of proteins (e.g.

Controlled synthesis of ultrathin ZnO nanowires using micellar gold nanoparticles as catalyst templates.

We demonstrate a simple and effective approach to control the diameter of ultrathin ZnO nanowires with high aspect ratios and high densities over large areas. Diblock copolymer-based nanoparticle arrays exhibiting a high degree of hexagonal order and offering easy control of particle size (typically 1-10 nm) and interparticle spacing (25-150 nm) are utilized as nanocatalysts for the subsequent growth of semiconductor nanowires. The as-grown ZnO nanowires exhibit a single crystal hexagonal wurtzite structure and grow along the [0002] direction.

A molecular toolkit for the functionalization of titanium-based biomaterials that selectively control integrin-mediated cell adhesion.

We present a click chemistry-based molecular toolkit for the biofunctionalization of materials to selectively control integrin-mediated cell adhesion. To this end, α5β1-selective RGD peptidomimetics were covalently immobilized on Ti-based materials, and the capacity to promote the selective binding of α5β1 was evaluated using a solid-phase integrin binding assay. This functionalization strategy yielded surfaces with a nine-fold increased affinity for α5β1, in comparison to control samples, and total selectivity against the binding of the closely related integrin αvβ3.

Evidence for phase separation of ethanol-water mixtures at the hydrogen terminated nanocrystalline diamond surface.

Interactions between ethanol-water mixtures and a hydrophobic hydrogen terminated nanocrystalline diamond surface, are investigated by sessile drop contact angle measurements. The surface free energy of the hydrophobic surface, obtained with pure liquids, differs strongly from values obtained by ethanol-water mixtures. Here, a model which explains this difference is presented.

Relationship between structural changes, hydrogen content and annealing in stacks of ultrathin Si/Ge amorphous layers.

Hydrogenated multilayers (MLs) of a-Si/a-Ge have been analysed to establish the reasons of H release during annealing that has been seen to bring about structural modifications even up to well-detectable surface degradation. Analyses carried out on single layers of a-Si and a-Ge show that H is released from its bond to the host lattice atom and that it escapes from the layer much more efficiently in a-Ge than in a-Si because of the smaller binding energy of the H-Ge bond and probably of a greater weakness of the Ge lattice. This should support the previous hypothesis that the structural degradation of a-Si/a-Ge MLs primary starts with the formation of H bubbles in the Ge layers.

Metallization of ultra-thin, non-thiol SAMs with flat-lying molecular units: Pd on 1, 4-dicyanobenzene.

Self-assembled monolayers of 1,4-dicyanobenzene on Au(111) electrodes are studied by cyclic voltammetry, in-situ STM and ex-situ XPS. High-resolution STM images reveal a long-range order of propeller-like assemblies each of which consists of three molecules, all lying flat on the gold substrate with the cyano groups oriented parallel to the metal surface. It is demonstrated that both functional groups can act as complexation sites for metal ions from solution.