Cell-Stress-Free Percutaneous Bioelectrodes.

Wearable bioelectronics have advanced dramatically over the past decade, yet remain constrained by their superficial placement on the skin, which renders them vulnerable to environmental fluctuations and mechanical instability. Existing microneedle (MN) electrodes offer minimally invasive access to dermal tissue, but their rigid, bulky design-often 100 times larger and 10,000 times stiffer than dermal fibroblasts-induces pain, tissue damage, and chronic inflammation, limiting their long-term applicability. Here, a cell-stress-free percutaneous bioelectrode is presented, comprising an ultrathin (<2 µm), soft MN (sMN) that dynamically softens via an effervescent structural transformation after insertion.

Multiscale, porous anion-exchangeable sponge for sustainable and convenient boron removal.

To address the limitations, such as complex treatment processes, reduced durability, and poor reusability, of typical micro- and nanoscale adsorbents for boron removal, a simple method for removing residual boron is introduced using a multiscale porous anion-exchangeable sponge (MP-AES) that electrostatically attracts boron in areas with locally high pH. Because commercially available anion-permselective materials are absent, custom nanoporous materials surrounded by microporous melamine foam are used to increase surface area and durability under repeated compression. The hydrophilic porous sponge facilitates liquid diffusion, enhancing adsorption in the user-friendly system.

Saline based microfluidic soft pressure sensor utilizing a three-dimensional focused electric field for motion and healthcare monitoring.

This paper introduces the 'Spatially Focused Saline-based Pressure Sensor (SF-SaPS)', a novel soft microfluidic pressure sensor featuring a distinctive three-dimensional focusing structure. By critically reducing the cross-sectional area of the microchannel at the focused structure, the SF-SaPS achieves excellent sensitivity to pressure within the sensing region. With the spatially focused region, the SF-SaPS could detect a wide range of pressure from gentle touches to human weight, which is typically unachievable with low-conductivity sensing media such as saline, a medium inherently safe for human use.

Design of 3D Controller Using Nanocracking Structure-Based Stretchable Strain Sensor.

In this study, we introduce a novel design for a three-dimensional (3D) controller, which incorporates the omni-purpose stretchable strain sensor (OPSS sensor). This sensor exhibits both remarkable sensitivity, with a gauge factor of approximately 30, and an extensive working range, accommodating strain up to 150%, thereby enabling accurate 3D motion sensing. The 3D controller is structured such that its triaxial motion can be discerned independently along the X, Y, and Z axes by quantifying the deformation of the controller through multiple OPSS sensors affixed to its surface.

Correction: Fully-automated and field-deployable blood leukocyte separation platform using multi-dimensional double spiral (MDDS) inertial microfluidics.

Correction for 'Fully-automated and field-deployable blood leukocyte separation platform using multi-dimensional double spiral (MDDS) inertial microfluidics' by Hyungkook Jeon , , 2020, , 3612-3624, https://doi.org/10.1039/D0LC00675K.

Peripheral Microneedle Patch for First-Aid Hemostasis.

Despite the minimized puncture sizes and high efficiency, microneedle (MN) patches have not been used to inject hemostatic drugs into bleeding wounds because they easily destroy capillaries when a tissue is pierced. In this study, a shelf-stable dissolving MN patch is developed to prevent rebleeding during an emergency treatment. A minimally and site-selectively invasive hemostatic drug delivery system is established by using a peripheral MN (p-MN) patch that does not directly intrude the wound site but enables topical drug absorption in the damaged capillaries.

Four-Dimensional Visualization of Microscale Dynamics of Membrane Oil Fouling via Synchrotron Radiation Microcomputed Tomography.

Although oil-water separation technology via wettability-controlled membranes has emerged as a promising technology to treat oily wastewater, membrane fouling by faulents such as sludge flocs and colloids, and the consequent clogging of pores, severely degrades the efficiency of filtration systems. One of the main promotors of fouling by faulents is oil fouling, which is also a form of fouling itself. Despite considerable practical and academic interest in the analysis of oil-fouled membranes, direct visualization of the entire process of oil infiltration into hydrophilic membranes is still preliminary owing to (i) the similar optical contrast and physical density between oil and water, (ii) the low penetration depth of imaging methods, and (iii) the lack of 3D segmentation capability.

Investigation of correlative parameters to evaluate EUV lithographic performance of PMMA.

Investigations to evaluate the extreme ultraviolet (EUV) lithographic performance of 160 nm thick poly(methyl methacrylate) with 13.5 nm wavelength EUV light were performed using a synchrotron radiation source at Pohang Light Source-II (PLS-II). The single system enabled the determination of the sensitivity, contrast, linear absorption coefficient, critical dimension, and line edge roughness of polymer thin films through tests and measurements.

Three-Axis Tension-Measuring Vitreoretinal Forceps Using Strain Sensor for Corneal Surgery.

Precise motion control is important in robotic surgery, especially corneal surgery. This paper develops a new tension-measurement system for forceps used in corneal surgery, wherein contact force is applied only to a specific location for precise control, with precise movements detected by attaching a nano-crack sensor to the corresponding part. The nano-crack sensor used here customizes the working range and sensor sensitivity to match the strain rate of the tip of the forceps.

Comprehensive Electrokinetic-Assisted Separation of Oil Emulsion with Ultrahigh Flux.

Many industries have a significant but largely unmet need for efficient and high-flux emulsion separation, particularly for nanoemulsions. Conventional separation membranes rely on size-based separation mainly utilizing a sieving mechanism plus a wetting phenomenon, resulting in a dramatic trade-off between separation efficiency and separation flux. Herein we address this challenge by adapting electrokinetics to membrane-based separation, using a charge-based mechanism capable of separating even nanoemulsions with a demonstrated separation efficiency of >99% and ultrahigh flux up to 40 000 L/H·m.

Fabrication of Oblique Submicron-Scale Structures Using Synchrotron Hard X-ray Lithography.

Oblique submicron-scale structures are used in various aspects of research, such as the directional characteristics of dry adhesives and wettability. Although deposition, etching, and lithography techniques are applied to fabricate oblique submicron-scale structures, these approaches have the problem of the controllability or throughput of the structures. Here, we propose a simple X-ray-lithography method, which can control the oblique angle of submicron-scale structures with areas on the centimeter scale.

Fully-automated and field-deployable blood leukocyte separation platform using multi-dimensional double spiral (MDDS) inertial microfluidics.

A fully-automated and portable leukocyte separation platform was developed based on a new type of inertial microfluidic device, multi-dimensional double spiral (MDDS) device, as an alternative to centrifugation. By combining key innovations in inertial microfluidic device designs and check-valve-based recirculation processes, highly purified and concentrated WBCs (up to >99.99% RBC removal, ∼80% WBC recovery, >85% WBC purity, and ∼12-fold concentrated WBCs compared to the input sample) were achieved in less than 5 minutes, with high reliability and repeatability (coefficient of variation, CV < 5%).

Direct Visualization of Microscale Dynamics of Water Droplets on under-Oil-Hydrophilic Membranes by Using Synchrotron White-Beam X-ray Microimaging Techniques.

Despite considerable academical and practical interests on separation of water-in-oil emulsion via special wettable membranes, fundamental understanding on microscale dynamics of water droplets on under-oil-hydrophilic membranes (UOHMs) at early stages during separation is still very preliminary due to temporal and spatial resolution of existing visualization techniques. To this end, we here succeed in a direct microscopic visualization of separation processes of water droplets on the UOHMs by employing a high-speed, two-dimensional synchrotron white-beam X-ray microimaging technique. During the separation of water-in-oil emulsion, microscale dynamic behaviors of water droplets on hydrophilic membrane surfaces immersed in the different oil media (i.

Highly-robust, solution-processed flexible transparent electrodes with a junction-free electrospun nanofiber network.

Flexible transparent electrodes (FTEs) are widely used in a variety of applications, including flexible displays and wearable devices. Important factors in FTE design include active control of electrical sheet resistance, optical transparency and mechanical flexibility. Because these factors are inversely proportional to one another, it is essential to develop a technique that maintains flexibility while actively controlling the sheet resistance and transparency for a variety of applications.

Fabrication of a Novel Nanofluidic Device Featuring ZnO Nanochannels.

We developed a novel fabrication method for nanochannels that are easily scaled up to mass production by selectively growing zinc oxide (ZnO) nanostructures and covering using a flat PDMS surface to make hollow nanochannels. Nanochannels are used in the biotechnological and environmental fields, being employed for DNA analysis and water purification, due to their unique features of capillary-induced negative pressure and an electrical double-layer overlap. However, existing nanochannel fabrication methods are complicated, costly, and not amenable to mass production.

Modulation of saliva pattern and accurate detection of ovulation using an electrolyte pre-deposition-based method: a pilot study.

We developed an electrolyte pre-deposition-based saliva pattern modulation method to detect ovulation with high accuracy and reliability. Ovulation tests using human saliva have advantages in terms of the earlier ovulation detection and more convenient sample collection procedure; however, accuracy is low, which is a critical limitation given that the concentrations of salivary constituents can vary depending on the health status of the tested individual and subjective user judgement of the test result. In this study, we quantitatively analyzed saliva patterns according to the concentrations of electrolytes and proteins in the ovulation test and found that changes in the saliva pattern during the ovulatory period can be controlled by sodium chloride (NaCl) pre-deposition, which directly affects the accuracy of ovulation detection.

Bio-inspired swellable hydrogel-forming double-layered adhesive microneedle protein patch for regenerative internal/external surgical closure.

Significant tissue damage, scarring, and an intense inflammatory response remain the greatest concerns for conventional wound closure options, including sutures and staples. In particular, wound closure in internal organs poses major clinical challenges due to air/fluid leakage, local ischemia, and subsequent impairment of healing. Herein, to overcome these limitations, inspired by endoparasites that swell their proboscis to anchor to host's intestines, we developed a hydrogel-forming double-layered adhesive microneedle (MN) patch consisting of a swellable mussel adhesive protein (MAP)-based shell and a non-swellable silk fibroin (SF)-based core.

An on-demand micro/nano-convertible channel using an elastomeric nanostructure for multi-purpose use.

Recently, nanochannels have been widely adopted in microfluidic systems, especially for biosensing and bio-concentrators. Here, we report an on-demand micro/nano-convertible channel, which consists of a simple configuration of elastic nanostructure underneath a single microchannel. By the degree of pressure applied by a pushrod, the microchannel starts to compress into a size-tunable micro- or nano-porous channel.

One-directional flow of ionic solutions along fine electrodes under an alternating current electric field.

Electric fields are widely used for controlling liquids in various research fields. To control a liquid, an alternating current (AC) electric field can offer unique advantages over a direct current (DC) electric field, such as fast and programmable flows and reduced side effects, namely the generation of gas bubbles. Here, we demonstrate one-directional flow along carbon nanotube nanowires under an AC electric field, with no additional equipment or frequency matching.

Recent Progress on Microelectrodes in Neural Interfaces.

Brain‒machine interface (BMI) is a promising technology that looks set to contribute to the development of artificial limbs and new input devices by integrating various recent technological advances, including neural electrodes, wireless communication, signal analysis, and robot control. Neural electrodes are a key technological component of BMI, as they can record the rapid and numerous signals emitted by neurons. To receive stable, consistent, and accurate signals, electrodes are designed in accordance with various templates using diverse materials.

Junction-free Flat Copper Nanofiber Network-based Transparent Heater with High Transparency, High Conductivity, and High Temperature.

Transparent conducting electrodes (TCE) are widely used in a variety of applications including displays, light-emitting diodes (LEDS), and solar cells. An important factor in TCE design is active control of the sheet resistance and transparency; as these are inversely proportional, it is essential to develop a technology that can maintain high transparency, while actively controlling sheet resistance, for a range of applications. Here, a nanofiber network was fabricated based on direct electrospinning onto a three-dimensional (3-D) complex substrate; flat metal electrodes without junction resistance were produced using heat treatment and electroless deposition.

Fabrication of Polymer Microstructures of Various Angles via Synchrotron X-Ray Lithography Using Simple Dimensional Transformation.

In this paper, we developed a method of fabricating polymer microstructures at various angles on a single substrate via synchrotron X-ray lithography coupled with simple dimensional transformations. Earlier efforts to create various three-dimensional (3D) features on flat substrates focused on the exposure technology, material properties, and light sources. A few research groups have sought to create microstructures on curved substrates.

Fabrication of Optical Switching Patterns with Structural Colored Microfibers.

Structural color was generated using electrospinning and hydrothermal growth of zinc oxide (ZnO). An aligned seed layer was prepared by electrospinning, and the hydrothermal growth time control was adjusted to generate various structural colors. The structural color changed according to the angle of the incident light.

Corrigendum: Purification of High Salinity Brine by Multi-Stage Ion Concentration Polarization Desalination.

This corrects the article DOI: 10.1038/srep31850.