Category Ranking
98%
Total Visits
921
Avg Visit Duration
2 minutes
Citations
20
Article Abstract
Objective: To evaluate the influence of in situ acid erosion on the structural and optical properties of nanoparticulate bisacrylic resin with different surface treatments, evaluating surface roughness (Ra), knoop microhardness (KHN), color change (ΔE, ΔL, ΔC, ΔH), contrast (CR) and translucency (TP).
Methods: Eighty specimens were made (n = 10 per group) and the following surface treatments were applied: U -unpolished; A -polishing with Astropol rubber tips (Ivoclar); S -Biscover LV surface sealant (Bisco) and S -Palaseal surface sealant (kulzer). For the in situ experiment, 10 volunteers wore an intraoral appliance containing eight specimens (two specimens per experimental group), with only one specimen from each experimental group being subjected to the acid process. They were immersed in 150 mL of cola-based soda (pH = 2.3), 4 × 5 min/day for 14 consecutive days evaluating surface roughness (Ra), knoop microhardness (KHN), color change by CIEDE2000 (ΔE, ΔL, ΔC, ΔH), contrast (CR) and translucency (TP).
Results: The S and S groups adopted the lowest Ra values, with a significant difference from the others. The S group had the highest values of KHN and NP the lowest, with a significant difference from the others. The S group had the highest values of ΔE00, being the only one with a significant difference from the others. In all analyses, there was no significant change between the groups without and with acid administration.
Conclusion: The surface sealants were able to improve the surface roughness and microhardness of the bisacrylic resin, however, the Palaseal sealant generates unacceptable color change. The acid injection did not significantly influence the properties of the material, regardless of the surface treatment performed.
Download full-text PDF |
Source |
|---|---|
| http://dx.doi.org/10.1111/jerd.13411 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
This in vitro study examined the influence of aging in different beverage solutions on the Knoop hardness and surface roughness of provisional fixed denture materials. A total of 160 resin blocks were created and divided into 4 groups (n = 40) based on the provisional material: Structur 2 SC bis-acrylic resin, Protemp 4 bis-acrylic resin, Z350 XT nanoparticle composite resin, or Acri Duralay acrylic resin. The material groups were subdivided into 4 groups (n = 10) according to the beverage solution used to simulate aging: distilled water (control), red wine, orange juice, or soda (Coca-Cola).
View Article and Find Full Text PDFImpact of material and silicone index support using additively manufactured trays on the reproducibility of diagnostic trial restorations (mock-up): A comparative in-vitro study.
J Dent
July 2025
Professor, Division of Fixed Prosthodontics and Biomaterials, University Clinics for Dental Medicine, University of Geneva, Geneva, Switzerland.
Objectives: To investigate the impact of material selection and silicone index support, provided by an additively manufactured tray, on the trueness of diagnostic trial restorations (mock-ups), fabricated using bis-acrylic resin loaded into silicone indexes.
Methods: A scan of a fully dentate patient was obtained, and diagnostic virtual waxing was performed to create two different designs: one representing a purely additive and the other featuring a combination of additive and non-additive approach. For each design, 60 silicone indexes were fabricated and divided into six groups.
Evaluation of Shear Bond Strength of Various Chairside Reline Materials to 3D Printed Provisional Crown Resins Following Surface Treatment.
J Pharm Bioallied Sci
June 2025
Department of Oral and Maxillofacial Rehabilitation, Faculty of Dentistry, King Abdulaziz University, Jeddah, Saudi Arabia.
Background: The reline material and interim base should bond well in provisional restorations. Few research examined 3D-printed restoration-relining bonding. To test the shear bond strength (SBS) of chairside crown reline materials to microfilled hybrid 3D-printed resin (PR) utilizing different surface treatments and materials.
View Article and Find Full Text PDFSurface roughness of 3D printed and conventional interim restorative materials after dynamic loading.
Am J Dent
April 2025
Department of Prosthodontics, Marmara University Faculty of Dentistry, Istanbul, Turkey.
Purpose: To investigate the surface roughness (Ra; µm) of three different interim resin materials, which were subjected to chewing simulation.
Methods: Three interim resin materials were evaluated: (1) LCD type (liquid crystal displays) 3D printed (LCD, n= 10); (2) conventional autopolymerizing bis-acrylic (CO, n= 10); (3) DLP type (digital light processing) 3D printed (DLP, n= 10) interim resin materials. The specimens were subjected to 30,000 cycles of chewing simulation.
Objective: To evaluate, in situ, the color stability of a printed resin (PR), milled resin (MR), and bisacrylic resin (BR) after exposure to coffee and cigarette smoke.
Materials And Methods: Twelve participants per group (Control, coffee consumers, and smokers) used intraoral devices containing the specimens resins. Seventy-two samples of each resin were prepared, and initial surface roughness and color readings recorded.