98%
921
2 minutes
20
Purpose: Surgeons placing implants use navigation for implant placement accuracy. The importance of this review is to document the sources of error that are involved with navigation so surgeons can recognize factors to decrease error. The objective is to provide surgeons with a reference to optimize navigation.
Methods: Pubmed.gov was the information source. Years reviewed included 2010 to 2022. The inclusion criteria included only articles in peer-reviewed journals. In vitro results were included only if they involved testing of variables microgap, cone beam computerized tomography (CBCT) accuracy evaluation, or accuracy of printed models. Variables were searched and evaluated. Data collected included the objectives and outcomes of the study including statistical significance. The conclusions made by the authors were confirmed by evaluating the data analysis, and then these conclusions were listed in each error-related topic.
Results: The search used terms which included guided implant surgery complications (n = 4,029), accuracy of CBCT scanners (n = 319), accuracy of implant navigation (n = 983), and the error between drills and static guides (n = 3). From this search, 70 articles were collated that satisfied the inclusion criteria. There are multiple sources of error that are less than 1 mm, including but not limited to errors associated with the scanner and method for scanning, errors associated with merging scanned files with the CBCT scan, errors using different guide stent fabrication methods, errors associated with intraoperative techniques, the learning curve, and planning error. If small errors are not taken into consideration, implant placement errors can exceed 1-2 mm of platform location and angulation errors in excess of 8°.
Conclusion: The surgeon needs to take into consideration controllable factors that will result in the avoidance of implant malposition and thus be able to effectively utilize navigation for accurate implant placement.
Download full-text PDF |
Source |
---|---|
http://dx.doi.org/10.1016/j.joms.2022.11.003 | DOI Listing |
Acta Ortop Mex
September 2025
Servicio de Ortopedia y Traumatología, Hospital de San Rafael, Hospitales Pascual. Cádiz, España.
Introduction: anatomical deformities such as developmental dysplasia of the hip (DDH) and Perthes disease represent a challenge for reconstruction. The use of 3D-printed models can be helpful for assessing the deformity, bone mass, implant size, and orientation.
Objectives: to prospectively evaluate the outcomes of 3D simulation in primary total hip arthroplasty.
Laryngoscope
September 2025
Buckingham Center for Facial Plastic Surgery, Austin, Texas, USA.
Hypoglossal nerve stimulation (HNS) device placement for moderate to severe obstructive sleep apnea has been growing in popularity. The incidence of patients requesting cervical rhytidectomy following implant placement is likely to increase proportionally to the incidence of device placement. This case report describes the preoperative and introperative considerations and details of successful rhytidectomy with platysmaplasty surgery with previous HNS device placement.
View Article and Find Full Text PDFAdv Healthc Mater
September 2025
Krembil Research Institute, Toronto Western Hospital, University Health Network, Toronto, ON, M5T 0S8, Canada.
Accurate brain signal recording and precise electrode placement are critical for the success of neuromodulation therapies such as deep brain stimulation (DBS). Addressing these challenges requires deep brain electrodes that provide high-quality, stable recordings while remaining compatible with high-resolution medical imaging modalities like magnetic resonance imaging (MRI). Moreover, such electrodes shall be cost-effective, easy to manufacture, and patient-compatible.
View Article and Find Full Text PDFCureus
August 2025
Department of Oral and Maxillofacial Surgery, University College of Medicine and Dentistry, The University of Lahore, Lahore, PAK.
Background And Aim: The incisive (nasopalatine) canal is an important anatomical structure of the anterior maxilla. It holds significance for surgeries and implant placement in the central incisor region. The size, shape, and relation with surrounding bones may vary by age, gender, and ethnicity.
View Article and Find Full Text PDFInt J Numer Method Biomed Eng
September 2025
Joint Reconstruction Research Center, Tehran University of Medical Sciences, Tehran, Iran.
The need for total knee arthroplasty (TKA) has grown significantly in recent years. The cutting angle in TKA plays a major role in the functionality and life expectancy of the knee implant components. This study aims to personalize the femur bone cutting angle selection for implant placement.
View Article and Find Full Text PDF