98%
921
2 minutes
20
Objectives: To evaluate the oncologic and functional results of scapular reconstruction after partial or total scapulectomy for chondrosarcoma.
Materials And Methods: Twenty-one patients with chondrosarcoma who underwent partial or total scapulectomy between January 2005 and July 2019 were reviewed retrospectively.
Results: At a mean follow-up of 62.6 months (range, 13-123 months), four patients developed local recurrence, and three developed distant metastases, one of which developed both recurrence and metastasis. The overall survival rate of patients at 5 years was 84.6%, the disease-free survival rate was 69.3%, and the complication rate was 19% (4/21). The 1993 American Musculoskeletal Tumor Society (MSTS93) scores of patients in the partial scapulectomy group, total scapulectomy + humeral suspension group and prosthetic reconstruction group were 26.50 ± 1.38, 19.00 ± 2.58, and 21.38 ± 2.62, respectively. There was a statistically significant difference between the partial scapulectomy group and the total scapulectomy + humeral suspension or prosthetic reconstruction group ( P = 0.006 and 0.0336, respectively). The range of motion of the shoulder joint for forward flexion was 80.83° ± 11.14°, 51.25° ± 21.36°, and 52.50° ± 11.02°, respectively. The p-values for the comparison between the partial scapulectomy group and the total scapulectomy + humeral suspension or prosthetic reconstruction group were 0.0493 and 0.0174, respectively. And the range of motion of abduction was 75.00° ± 10.49°, 32.50° ± 11.90°, 41.88° ± 11.63°, respectively. Patients in the partial scapulectomy group had significantly better postoperative shoulder abduction function than the total scapulectomy + humeral suspension or prosthetic reconstruction group (P = 0.0035 and 0.0304, respectively). There was no significant difference in MSTS93 scores and flexion and abduction function of the shoulder joint in the upper extremity after total scapulectomy with humeral suspension or prosthetic reconstruction (P > 0.05).
Conclusions: Surgical treatment of chondrosarcoma of the scapula can achieve a satisfactory prognosis and shoulder function. Total scapulectomy followed by prosthetic reconstruction or humeral suspension are both feasible treatments.
Download full-text PDF |
Source |
---|---|
http://www.ncbi.nlm.nih.gov/pmc/articles/PMC9358882 | PMC |
http://dx.doi.org/10.1186/s12891-022-05661-7 | DOI Listing |
J Prosthodont
September 2025
Department of Reconstructive Dentistry and Gerodontology, School of Dental Medicine, University of Bern, Bern, Switzerland.
Purpose: This study aimed to evaluate the inherent and after cyclic loading fracture strength of implant-supported cantilevered fixed prostheses fabricated from recently introduced additively manufactured (AM) and subtractively manufactured (SM) materials, considering variations in prosthesis height.
Materials And Methods: Three cylinder-shaped master files (20 mm long and 11 mm wide) with varying heights (7, 11, and 15 mm) and a titanium-base (Ti-base) abutment space were designed. These designs were used to fabricate a total of 144 specimens with two AM resins indicated for definitive use (Crowntec; AM-CT and Flexcera Smile Ultra+; AM-FS), one high-impact polymer composite (breCAM.
J Prosthodont
September 2025
Department of Reconstructive Dentistry and Gerodontology, School of Dental Medicine, University of Bern, Bern, Switzerland.
Purpose: This study aimed to compare the dimensional and positional deviations of additively manufactured removable dies fabricated using two bio-based resins and one conventional dental cast resin, while also evaluating these outcomes over a 4-week period.
Materials And Methods: A right mandibular first molar preparation on a typodont was scanned to digitally design removable dies and hollow partial arch casts. Based on a priori power analysis, a total of 30 dies (n = 10) and three hollow casts (n = 1) were fabricated using additive manufacturing (AM) from three different dental cast resins: DentaMODEL (DM), FotoDent bio-based model (CB), and soy-based resin (SB).
Int J Oral Implantol (Berl)
September 2025
Purpose: To present a novel digital workflow (the Columbus Digital Bridge Protocol) for immediately loaded full-arch rehabilitations, integrating digital technologies throughout diagnostic, surgical and prosthetic phases, with a focus on the application of intraoral photogrammetry scanning.
Materials And Methods: The workflow presented in this article, successfully implemented in 14 patients, includes standardised clinical steps: digital diagnostic planning through matching of facial scans and CBCT data, surgical placement of four implants following tooth extraction, immediate post-surgical intraoral photogrammetry scanning using a three-step procedure (i.e.
Cureus
August 2025
Dental and Oral Medical Center, Kurume University School of Medicine, Kurume, JPN.
Functional reconstruction of large mandibular defects, especially in young patients, presents a significant clinical challenge. The ideal approach should not only restore skeletal contour but also address nerve deficits and facilitate final occlusal rehabilitation, all while minimizing morbidity. This report describes a comprehensive, multi-staged strategy for such a case.
View Article and Find Full Text PDFSurg Case Rep
August 2025
Department of Cardiac and Vascular Surgery, Dokkyo Medical University School of Medicine, Shimotsugagun, Tochigi, Japan.
Introduction: Prosthetic valve endocarditis following aortic root replacement (ARR) typically necessitates redo-ARR, which involves complete graft removal, extensive aortic root dissection, and coronary reimplantation. This highly invasive procedure carries substantial surgical risk, including high operative mortality. In select high-risk patients without evidence of prosthetic graft infection, alternative surgical strategies may reduce procedural complexity and improve outcomes.
View Article and Find Full Text PDF