98%
921
2 minutes
20
In view of the current trend of capacitor materials, the development of capacitors with high dielectric permittivity and low dielectric loss is of great interest. In this work, the dielectric permittivity of reduced graphene oxide-incorporated styrene-butyl acrylate (rGO@SBA) composite microspheres synthesized by mini-emulsion polymerization was significantly improved. rGO with 2 wt% content gave a dielectric permittivity of 11 356 (at 1 KHz), which was 1925 times higher than that of pure SBA (5.9). SEM and TEM were conducted to observe the morphology and structure of the composite microspheres. After filling into polystyrene (PS), a segregated structure of (rGO@SBA) that enables a concentrated aggregation of rGO in SBA was fabricated. The dielectric permittivity of PS could reach 10.91 (at 1 KHz) by incorporating only 0.39 wt% rGO by using this segregated structure of (rGO@SBA). PS simply mixed with SBA microspheres and graphite (PS/rGO-SBA) was also fabricated as a comparison group to verify the effect of this segregated structure on the dielectric properties of the composites. After comparing the dielectric properties of PS composites with different structures, the enhancement in dielectric permittivity of the composites can be demonstrated.
Download full-text PDF |
Source |
---|---|
http://www.ncbi.nlm.nih.gov/pmc/articles/PMC9284524 | PMC |
http://dx.doi.org/10.1039/d2ra03427a | DOI Listing |
RSC Adv
August 2025
Institute of Nanoscience and Nanotechnology, National Center for Scientific Research "Demokritos" Agia Paraskevi 15341 Greece.
In this study, porous polysiloxane (PS)/multi-walled carbon nanotube (MWCNT) nanocomposite films were developed as high-performance triboelectric layers for flexible triboelectric nanogenerators (TENGs). TENGs convert mechanical motion into electricity and offer a promising solution for self-powered electronic systems. The nanocomposites were fabricated using a doctor blading method, and porosity was introduced a simple, scalable salt-leaching technique.
View Article and Find Full Text PDFThe functionalization of thin, flexible glass with piezoelectric oxides is a pathway toward transparent electromechanical devices. The crystallization of lead zirconate titanate thin films on thick, rigid glass is previously demonstrated using flash lamp annealing to selectively anneal the films, without damaging the substrates. In this work, a 2-step process suitable for Schott AF 32 eco glass and Corning Willow glass is developed, both 100 μm thick, the latter of which is compatible with roll-to-roll processes.
View Article and Find Full Text PDFSmall
September 2025
Department of Mechanical Engineering, The Hong Kong Polytechnic University, Hong Kong, 999077, China.
Droplet electricity generators (DEGs) that generate electricity through the interplay between water and the dielectric materials have attracted growing research interest due to their remarkable output voltage. However, conventional DEG design faces a critical trade-off: regulating the properties of dielectric materials, such as thickness or permittivity, can enhance output voltage yet weaken transferred charge. Here, a fluorinated ethylene propylene (FEP)/multi-walled carbon nanotubes (MWCNTs)/polydimethylsiloxane (PDMS) composite-based droplet electricity generator (FMP-DEG) is presented to overcome the voltage-charge trade-off and thus achieve an enhanced energy conversion efficiency of 4.
View Article and Find Full Text PDFAnal Bioanal Chem
August 2025
Nick Holonyak Jr. Micro and Nanotechnology Laboratory, University of Illinois at Urbana-Champaign, Urbana, IL, 61801, USA.
The unique optical interaction of species such as nanomaterials, proteins, viruses, antibodies, microRNA, and exosomes with the one-dimensional grating-based photonic crystals (PCs) has been leveraged in their detection using photonic crystal absorption microscopy (PRAM). While the principle and fundamental mechanism of such interfacial interactions are well delineated using wavelength and intensity modulations associated with the guided-mode resonance (GMR) of the PC, the effect of nano-assemblies in place of nanoparticles (NPs) has not been reported previously. In this work, the fundamental limitations observed with pristine NPs are overcome through the use of tunable AuNP assemblies synthesized via adiabatic cooling technology, where tunable nano-assemblies are obtained by subjecting the respective NPs to - 196 °C.
View Article and Find Full Text PDFPolymers (Basel)
August 2025
Department of Electrical and Power Engineering, AGH University, 30-059 Kraków, Poland.
In the power industry, various electrically insulating materials are used to ensure proper mechanical, thermal, and dielectric performance over decades of equipment operation. In power transformers, cellulose is the predominant material in manufacturing various insulation components. Most of these products are manufactured by wet-molding technology.
View Article and Find Full Text PDF