Category Ranking
98%
Total Visits
921
Avg Visit Duration
2 minutes
Citations
20
Article Abstract
The whole-genome sequences of Mycobacterium chimaera strains 850 and 852, which were isolated from two different water samples obtained from a heater-cooler unit at Siena University Hospital (Italy), were determined by combining Nanopore and Illumina technologies. Genomes of both strains 850 and 852 consist of a circular chromosome and five plasmids, with sizes of 6,275,686 bp and 6,453,144 bp, respectively.
Download full-text PDF |
Source |
|---|---|
| http://www.ncbi.nlm.nih.gov/pmc/articles/PMC8772592 | PMC |
| http://dx.doi.org/10.1128/mra.01021-21 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Role and potential of artificial intelligence, robotics, and navigation-assisted technologies in the diagnosis, treatment, and prognosis of osteoporotic vertebral compression fractures.
Int J Surg
August 2025
Department of Spine Surgery, The Affiliated Jiangning Hospital of Nanjing Medical University, Nanjing, Jiangsu, China.
In recent years, there has been a rise in fractures caused by osteoporosis. Such fractures significantly contribute to bone morbidity and place an increasing strain on global healthcare systems. Among them, osteoporotic vertebral compression fractures (OVCFs) have shown a steady upward trend.
View Article and Find Full Text PDFThe development of high-power gain chips is crucial for advancing hybrid-integrated narrow-linewidth lasers, which face power limitations in emerging applications such as quantum sensing and atomic cooling. This study designed a high-power GaAs-based gain chip based on an asymmetric waveguide and compressively strained quantum wells for the 850 nm wavelength band. By applying the epitaxial structure and low-loss waveguide, a record continuous-wave output power of 114.
View Article and Find Full Text PDFDeformation Behaviors in Single BCC-Phase Refractory Multi-Principal Element Alloys under Dynamic Conditions.
Adv Sci (Weinh)
August 2025
Center for Integrated Nanotechnologies, MPA Division, Los Alamos National Laboratory, Los Alamos, NM, 87545, USA.
The mechanical behavior and microstructural evolution of a BCC-phase NbTaTiV refractory multi-principal element alloy (RMPEA) is studied over a wide range of strain rates (10 to 10 s) and temperatures (room temperature to 850 °C). The mechanical property of present RMPEA shows less strain-rate dependence and strong resistance to softening at high temperatures. Under high strain-rate loading, the formation of thin type-I twins is observed, which could lead to an increase in strain-hardening rates.
View Article and Find Full Text PDFCarrier-Based Application of Phyto-Benefic and Salt-Tolerant and for Sustainable Wheat Production Under Salinity Stress.
Plants (Basel)
July 2025
Department of Engineering and Technology, Punjab Tianjin University of Technology, Lahore 53720, Pakistan.
Plant growth-promoting rhizobacteria (PGPR) are beneficial soil microorganisms that enhance plant growth and stress tolerance through various mechanisms, including phytohormone production, EPS production, phosphate solubilization, and extracellular enzyme production. These bacteria establish endosymbiotic relationships with plants, improving nutrient availability and overall crop productivity. Despite extensive research on PGPR isolation, their practical application in agricultural fields has faced challenges due to environmental stresses and limited survival during storage.
View Article and Find Full Text PDFThe Effect of the Finishing Deformation Temperature on the Microstructure of CrVNb Micro-Alloyed Steel.
Materials (Basel)
July 2025
School of Mechanical, Materials, Mechatronic and Biomedical Engineering, University of Wollongong, Wollongong, NSW 2522, Australia.
This study explored the effects of the finishing deformation temperature on the microstructure and properties of CrVNb micro-alloyed steel following thermomechanical processing (TMP). The investigation encompassed the influence of the deformation temperature on the ferrite grain size, precipitate characteristics, hardness and flow stress. The microstructure characterization was performed using optical and electron microscopy techniques.
View Article and Find Full Text PDF