98%
921
2 minutes
20
Heteroepitaxy of β-phase gallium oxide (β-GaO) thin films on foreign substrates shows promise for the development of next-generation deep ultraviolet solar blind photodetectors and power electronic devices. In this work, the influences of the film thickness and crystallinity on the thermal conductivity of (2̅01)-oriented β-GaO heteroepitaxial thin films were investigated. Unintentionally doped β-GaO thin films were grown on -plane sapphire substrates with off-axis angles of 0° and 6° toward ⟨112̅0⟩ via metal-organic vapor phase epitaxy (MOVPE) and low-pressure chemical vapor deposition. The surface morphology and crystal quality of the β-GaO thin films were characterized using scanning electron microscopy, X-ray diffraction, and Raman spectroscopy. The thermal conductivities of the β-GaO films were measured via time-domain thermoreflectance. The interface quality was studied using scanning transmission electron microscopy. The measured thermal conductivities of the submicron-thick β-GaO thin films were relatively low as compared to the intrinsic bulk value. The measured thin film thermal conductivities were compared with the Debye-Callaway model incorporating phononic parameters derived from first-principles calculations. The comparison suggests that the reduction in the thin film thermal conductivity can be partially attributed to the enhanced phonon-boundary scattering when the film thickness decreases. They were found to be a strong function of not only the layer thickness but also the film quality, resulting from growth on substrates with different offcut angles. Growth of β-GaO films on 6° offcut sapphire substrates was found to result in higher crystallinity and thermal conductivity than films grown on on-axis -plane sapphire. However, the β-GaO films grown on 6° offcut sapphire exhibit a lower thermal boundary conductance at the β-GaO/sapphire heterointerface. In addition, the thermal conductivity of MOVPE-grown (2̅01)-oriented β-(AlGa)O thin films with Al compositions ranging from 2% to 43% was characterized. Because of phonon-alloy disorder scattering, the β-(AlGa)O films exhibit lower thermal conductivities (2.8-4.7 W/m·K) than the β-GaO thin films. The dominance of the alloy disorder scattering in β-(AlGa)O is further evidenced by the weak temperature dependence of the thermal conductivity. This work provides fundamental insight into the physical interactions that govern phonon transport within heteroepitaxially grown β-phase GaO and (AlGa)O thin films and lays the groundwork for the thermal modeling and design of β-GaO electronic and optoelectronic devices.
Download full-text PDF |
Source |
---|---|
http://dx.doi.org/10.1021/acsami.1c08506 | DOI Listing |
Adv Mater
September 2025
Dept. of Physics, Pennsylvania State University, University Park, PA, 16802, USA.
Altermagnets are a newly identified family of collinear antiferromagnets with a momentum-dependent spin-split band structure of non-relativistic origin, derived from spin-group symmetry-protected crystal structures. Among candidate altermagnets, CrSb is attractive for potential applications because of a large spin-splitting near the Fermi level and a high Néel transition temperature of around 700 K. Molecular beam epitaxy is used to synthesize CrSb (0001) thin films with thicknesses ranging from 10 to 100 nm.
View Article and Find Full Text PDFNat Commun
September 2025
Max-Born-Institut für Nichtlineare Optik und Kurzzeitspektroskopie, Berlin, Germany.
Light-induced magnetisation switching is one of the most intriguing and promising areas where an ultrafast phenomenon can be utilised in technological applications. So far, experiment and theory have considered the origin of all-optical helicity-independent magnetisation switching (AO-HIS) in individual magnetic films only as a microscopically local, thermally-driven process of angular momentum transfer between different subsystems. Here, we demonstrate that this local picture is insufficient and that AO-HIS must also be regarded as a spatially inhomogeneous process along the depth within a few-nanometre thin magnetic layer.
View Article and Find Full Text PDFCarbohydr Polym
November 2025
Department of Pharmacy - Pharmaceutical Sciences, University of Bari Aldo Moro, E. Orabona St., 70125 Bari, Italy.
Direct printing of pharmaceutical powders allows the creation of personalized paediatric dosage forms, such as orodispersible films (ODFs). In this study, we present an optimized protocol to prepare midazolam (MDZ)/γ-cyclodextrin (γ-CD) inclusion complex-loaded ODFs using the innovative direct powder extrusion 3D printing technique (DPE). ODFs were formulated with a polymer blend consisting of polyethylene oxide and hydroxypropyl methylcellulose, in the presence or without γ-CD.
View Article and Find Full Text PDFACS Appl Mater Interfaces
September 2025
Imec, Kapeldreef 75, 3001 Leuven, Belgium.
Extreme ultraviolet (EUV) lithography has revolutionized the high-volume manufacturing of nanoscale components. The use of EUV light leads to ionization-driven chemistry in the imaging materials of lithography, the photoresists. The complex interplay of ionization, generation of primary/secondary electrons, and the subsequent chemical mechanisms that lead to image formation in photoresists has been notoriously difficult to study.
View Article and Find Full Text PDFACS Appl Mater Interfaces
September 2025
Core Manufacturing Technology Research Institute, National Institute of Advanced Industrial Science and Technology (AIST), Tsukuba Central 5, 1-1-1 Higashi, Tsukuba, Ibaraki 305-8565, Japan.
The direct deposition of piezoelectric ceramic thin films onto metal foils has become a significant challenge due to the increasing demand for embedded decoupling capacitors, nanogenerators, and flexible piezo-sensors. However, traditional thermal sintering (TS) methods present several issues for metal foils, including alterations in mechanical properties, the formation of wrinkles, and the need for precise control over the sintering atmosphere to prevent oxidation. In this study, we successfully crystallized BaTiO on a Ni foil under atmospheric conditions, mitigating thermal damage to the foil through a hybrid-solution-incorporated photoassisted chemical solution deposition (HS-PCSD) method.
View Article and Find Full Text PDF