Category Ranking

98%

Total Visits

921

Avg Visit Duration

2 minutes

Citations

20

Article Abstract

Introduction: Most studies predicting survival after resection, transarterial chemoembolization (TACE), and ablation analyzed diameter and number of hepatocellular carcinomas (HCCs) as dichotomous variables, resulting in an underestimation of risk variation. We aimed to develop and validate a new prognostic model for patients with HCC using largest diameter and number of HCCs as continuous variables.

Methods: The prognostic model was developed using data from patients undergoing resection, TACE, and ablation in 645 Japanese institutions. The model results were shown after balanced using the inverse probability of treatment-weighted analysis and were externally validated in an international multi-institution cohort.

Results: Of 77,268 patients, 43,904 patients, including 15,313 (34.9%) undergoing liver resection, 13,375 (30.5%) undergoing TACE, and 15,216 (34.7%) undergoing ablation, met the inclusion criteria. Our model (http://www.u-tokyo-hbp-transplant-surgery.jp/about/calculation.html) showed that the 5-year overall survival (OS) in patients with HCC undergoing these procedures decreased with progressive incremental increases in diameter and number of HCCs. For patients undergoing resection, the inverse probability of treatment-weighted-adjusted 5-year OS probabilities were 10%-20% higher compared with patients undergoing TACE for 1-6 HCC lesions <10 cm and were also 10%-20% higher compared with patients undergoing ablation when the HCC diameter was 2-3 cm. For patients undergoing resection and TACE, the model performed well in the external cohort.

Discussion: Our novel prognostic model performed well in predicting OS after resection and TACE for HCC and demonstrated that resection may have a survival benefit over TACE and ablation based on the diameter and number of HCCs.

Download full-text PDF

Source
http://dx.doi.org/10.14309/ajg.0000000000001256DOI Listing

Publication Analysis

Top Keywords

diameter number
16
patients undergoing
12
number hepatocellular
8
hepatocellular carcinomas
8
survival resection
8
resection transarterial
8
transarterial chemoembolization
8
tace ablation
8
prognostic model
8
patients hcc
8

Similar Publications

Aim: To describe the percentage of abdominal aortic aneurysm (AAA) cases in the Maspalomas Basic Health Zone among males aged 65 to 75 years who are current or former smokers. Our secondary objectives were to define the distribution of known risk factors for AAA development in our sample and to facilitate early referral to the appropriate vascular surgery service. We also aim to describe the percentage of subaneurysm cases, offering ultrasound follow-up at our center.

View Article and Find Full Text PDF

Background: Vitrified embryos ≤300 μm give better pregnancy rates following warming and transfer than larger ones. Embryo recovery undertaken close to when the embryo enters the uterus (Day 6-6.5) helps in the recovery of embryos ≤300 μm.

View Article and Find Full Text PDF

Homeostasis and thermoregulation depend on the interplay of the hair and skin. Maternal heat stress in late gestation triggers postnatal hair and skin adaptations in daughters and granddaughters. Herein, we investigated the transgenerational effects of late-gestation heat stress on the hair and skin of the great-granddaughters.

View Article and Find Full Text PDF

Objective: The distal transradial approach has been one of the options for endovascular neurointervention because of the low risk of puncture site complications. However, the conventional and distal transradial artery approaches frequently cause cannulation-induced vasospasms, which can usually be prevented by vasodilators. The aim was to evaluate the effects of local infiltration using a puncture site cocktail of lidocaine mixed with nitroglycerin on puncture success and vasospasm for distal transradial cerebral angiography.

View Article and Find Full Text PDF

3D-Printed Microfiltration Membranes via Dual-Wavelength Microstereolithography.

ACS Omega

September 2025

Aerospace Structures and Materials Department, Faculty of Aerospace Engineering, Delft University of Technology, Kluyverweg 1, Delft 2629HS, The Netherlands.

A new and sustainable membrane manufacturing method is 3D printing, which reduces the number of fabrication steps, waste production, and the corresponding CO emissions. It further enables fabricating membranes with well-defined pore size, shape, and configuration. Here, we study 3D printing of microfiltration membranes using a novel dual-wavelength microstereolithography method.

View Article and Find Full Text PDF