Category Ranking
98%
Total Visits
921
Avg Visit Duration
2 minutes
Citations
20
Article Abstract
The thin layered graphitic carbon nitride (-CN) was prepared by the thermal polymerization process with urea as the precursor. The layered heterostructure of graphitic carbon nitride-bismuth oxyiodide (-CN/BiOI) was constructed by the in-situ synthetization of bismuth oxyiodide (BiOI) on the surface of the thin layered -CN. The morphology, specific surface area, crystal structure, molecular structure, light absorption properties, and surface properties were characterized by TEM, BET, XRD, FT-IR, UV-Vis DRS, and XPS, respectively. The disinfection performance of the synthesized catalysts under visible light irradiation was investigated. The antibacterial mechanism of -CN/BiOI in the photocatalytic process was further revealed by the capture of sacrificial agents. The results indicate that the prepared sample has a layered heterojunction structure with a specific surface area of 63 m·g and its light absorption side can obtain 600 nm. The results of the photocatalytic activity test indicate that -CN/BiOI can kill bacteria within 4 h, which is significantly higher than that of -CN and BiOI. The main active species of -CN/BiOI in the photocatalytic process can be attributed to the photogenerated holes.
Download full-text PDF |
Source |
|---|---|
| http://dx.doi.org/10.13227/j.hjkx.201702014 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Tellurium-Nitrogen-Carbon Support Boosting Platinum Catalysis in High-Efficiency Proton Exchange Membrane Fuel Cells.
Angew Chem Int Ed Engl
September 2025
State Key Laboratory of Advanced Technology for Materials Synthesis and Processing, Wuhan University of Technology, Wuhan, 430070, China.
Enhancing the energy conversion efficiency of fuel cells necessitates optimization of oxygen reduction reaction (ORR) under high-voltage conditions through improved Pt catalysis. This study introduces an electrocatalyst that uniformly anchors a high loading (40 wt%) of small Pt nanoparticles (3.2 nm) on a novel support: tellurium and nitrogen co-mediated graphitized mesoporous carbon (Te-N-GMC).
View Article and Find Full Text PDFLithium Metal Ingrowth Toward a Porous Structure via Coble Creep along Lithium-Carbon Interface Without Ionic Conductors.
Small
September 2025
School of Energy and Chemical Engineering, UNIST, Ulsan, 44919, South Korea.
All-solid-state batteries (ASSBs), equipped with highly ion-conductive sulfide solid electrolytes and utilizing lithium plating/stripping as anode electrochemistry, suffer from 1) chemical vulnerability of the electrolytes with lithium and 2) physical growth of lithium to penetrate the electrolytes. By employing an ordered mesoporous graphitic carbon (OMGC) framework between a sulfide electrolyte layer and a copper current collector in ASSB, the concerns by are addressed 1) minimizing the chemically vulnerable interface (CVI) between electric conductor and solid electrolyte, and 2) allowing lithium ingrowth toward the porous structure via Coble creep, a diffusional deformation mechanism of lithium metal along the lithium-carbon interface. The void volume of the framework is fully filled with lithium metal, despite ionic pathways not being provided separately, even without additional lithiophiles, when an enough amount of lithium is allowed to be plated.
View Article and Find Full Text PDFInhibiting Graphite Co-Intercalation through Weak Solvating Ether Electrolytes for Stable Cycling in Potassium-Ion Batteries.
J Phys Chem Lett
September 2025
Faculty of Material Science and Chemistry, China University of Geosciences, Wuhan 430074, China.
Ether-based electrolytes are widely acknowledged for their potential to form stable solid electrolyte interfaces (SEIs) for stable anode performance. However, conventional ether-based electrolytes have shown a tendency for cation-solvent co-intercalation phenomena on graphite electrodes, resulting in lower capacity and higher voltage platforms compared to those of neat cation insertion in ester-based electrolytes. In response, we propose the development of weakly solvating ether solvents to weaken the interaction between cations and solvents, thereby suppressing co-intercalation behavior.
View Article and Find Full Text PDFDual-synergistic molybdenum disulfide and molybdenum carbide cocatalyst integrated with graphitic carbon nitride for efficient photocatalytic hydrogen production.
J Colloid Interface Sci
September 2025
Department of Thermal Science and Energy Engineering, University of Science and Technology of China, 96 Jinzhai Road, Hefei 230026, PR China. Electronic address:
Heterojunctions have garnered significant attention in the field of photocatalysis due to their exceptional ability to facilitate the separation of photogenerated charge carriers and their high efficiency in hydrogen reaction. However, their overall photocatalytic performance is often constrained by electron transport rates and suboptimal hydrogen adsorption/desorption kinetics. To address these challenges, this study develops a g-CN/MoS@MoC dual-effect synergistic solid-state Z-type heterojunction, synthesized through the in-situ sulfurization of MoC combined with ultrasonic self-assembly technique.
View Article and Find Full Text PDFBoosting Sodium Storage in Hard Carbon: A Low-Temperature Ball Milling Approach for Superior Anode Performance.
Langmuir
September 2025
College of Materials and Chemistry & Chemical Engineering, Chengdu University of Technology, Chengdu 610059, PR China.
Hard carbon (HC) has emerged as a promising anode material for sodium-ion batteries (SIBs) owing to its superior sodium storage performance. However, the high cost of conventional HC precursors remains a critical challenge. To address this, coal─a low-cost, carbon-rich precursor─has been explored for HC synthesis.
View Article and Find Full Text PDF