Category Ranking
98%
Total Visits
921
Avg Visit Duration
2 minutes
Citations
20
Article Abstract
This study investigated the shear bond strength (SBS) between veneering porcelain and zirconia substructure using lithium disilicate glass-ceramic as a liner. The mineral phases and microstructures of lithium disilicate glass-ceramic at temperature range of 800-900°C were preliminarily investigated. SBSs of porcelain-veneered zirconia specimens with and without lithium disilicate glassceramic liner fired at the same temperature were determined. Results showed that SBSs of veneering porcelain and zirconia with lithium disilicate glass-ceramic liner was notably increased (p<0.05). Specimens from the group with the highest SBS (59.7 MPa) were subject to thermocycling up to 10,000 cycles and their post-thermocycling SBSs investigated. Though weakened by thermocycling, SBSs were above the clinically acceptable limit (25 MPa) of ISO 9693. Fractographic analysis revealed mixed cohesive and adhesive failures. It was concluded that lithium disilicate glass-ceramic is a potential liner which generated high SBS between veneering porcelain and zirconia.
Download full-text PDF |
Source |
|---|---|
| http://dx.doi.org/10.4012/dmj.2014-319 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Impact of Ceramic Composition and Thickness on Light Transmission in CAD/CAM Lithium Disilicate Materials: An In Vitro Study.
Int J Dent
August 2025
Department of Prosthodontics, The University of Iowa College of Dentistry and Dental Clinics, Iowa City 52242, Iowa, USA.
This study investigates light transmission through five types of computer-aided design/computer-aided manufacturing (CAD/CAM) lithium disilicate ceramics, varying in thickness (0.50, 1.00, and 1.
View Article and Find Full Text PDFFatigue performance and failure load of minimally-invasive occlusal veneers made of lithium disilicate and composition-gradient multilayered zirconia: An in vitro study.
J Prosthodont Res
September 2025
Department of Prosthodontics, Medical Faculty and University Hospital Düsseldorf, Heinrich-Heine-University, Düsseldorf, Germany.
Purpose: To investigate the effect of ceramic material (lithium disilicate, LDS vs. composition-gradient multilayered zirconia [4Y-PSZ and 5-PSZ], Z) and ceramic layer thickness (0.5 mm, 1.
View Article and Find Full Text PDFEffect of food-simulating solvents on the stainability and mechanical properties of partially and fully crystallized lithium disilicate glass-ceramics.
J Prosthet Dent
September 2025
Associate Professor, Division of Restorative Sciences, Adams School of Dentistry, University of North Carolina at Chapel Hill, Chapel Hill, NC.
Statement Of Problem: The effect of food-simulating solvents (FSSs) on the staining susceptibility and mechanical properties of partially and fully crystallized lithium disilicate glass-ceramics (LDGCs) remains unclear.
Purpose: The purpose of this in vitro study was to evaluate the color change, hardness, flexural strength, and reliability of LDGCs exposed to FSSs.
Material And Methods: Two machinable LDGCs, partially crystallized (IPS e.
Internal and marginal fit of digitally fabricated all-ceramic crowns with auxiliary retentive features on short clinical abutments: a micro-CT study.
PeerJ
September 2025
Department of Dental Research Cell, Dr. D. Y. Patil Dental College and Hospital, Pune, Maharashtra, India.
Background: Short clinical crowns/abutments (SCC) pose a challenge in achieving adequate retention. Auxiliary retentive features (ARF), such as grooves, are commonly employed to enhance retention. The marginal gap (MG) and internal fit (IF) of restorations are critical factors influencing clinical success.
View Article and Find Full Text PDFColor Stability of Three Ceramics After Thermocycling in Coffee, Black Tea, Cola, and Water: An In Vitro Study.
Int J Dent
August 2025
Dental Sciences Research Center, School of Dentistry, Guilan University of Medical Sciences, Rasht, Iran.
Ceramic restorations have become a cornerstone of modern dentistry. Color stability is crucial for dental ceramics to maintain the esthetic appearance of restorations over time. Given the widespread consumption of staining agents like coffee, tea, and cola, this study aimed to assess the color stability of three ceramics after thermocycling in different solutions.
View Article and Find Full Text PDF