Adsorption Behavior and Kinetics of 1,4-Dioxane by Carbon Aerogel.

Toxics

Key Laboratory of Jiangxi Province for Persistent Pollutants Control and Resources Recycle, Nanchang Hangkong University, Nanchang 330063, China.

Published: February 2024


Category Ranking

98%

Total Visits

921

Avg Visit Duration

2 minutes

Citations

20

Article Abstract

1,4-dioxane is a potential carcinogen in water and is difficult to deal with due to its robust cycloether bond and complete miscibility with water. To remove 1,4-dioxane in an economically viable and environmentally friendly way, a series of carbon aerogels were synthesized as adsorbents for 1,4-dioxane. The experiment results showed that adsorption performances were closely related to the preparation conditions of carbon aerogels, such as the molar ratio, heating rate, pyrolysis temperature and residence time, which were carefully controlled. Scanning electron microscope analysis revealed the presence of a three-dimensional porous network structure in carbon aerogels. Brunauer-Emmett-Teller analysis results demonstrated an increase in specific surface area (673.89 m/g) and total pore volume after carbonization, with an increase in mesoporous porosity and a decrease in microporosity. When considering each variable individually, the highest specific surface area of prepared carbon aerogels was achieved at a pyrolysis temperature of 800 °C, a holding time of 1 h, and a heating rate of 2 °C/min. Under optimal experimental conditions, the adsorption removal of 1,4-dioxane by carbon aerogels exceeded 95%, following quasi-second-order kinetics and Langmuir isothermal adsorption isotherms, indicating that monolayer adsorption on the surface of carbon aerogels occurred. The maximum adsorption capacity obtained was 67.28 mg/g at a temperature of 318 K, which was attributed to the presence of a large proportion of mesopores and abundant micropores simultaneously in carbon aerogels. Furthermore, with the interference of chlorinated solvents such as trichloroethylene (TCE), the removal efficiency of 1,4-dioxane had no obvious inhibition effect. Regeneration experiments showed that after five continuous cycles, the carbon aerogels still kept a comparable adsorption capacity, which illustrates its potential application in 1,4-dioxane-polluted water purification.

Download full-text PDF

Source
http://www.ncbi.nlm.nih.gov/pmc/articles/PMC10893410PMC
http://dx.doi.org/10.3390/toxics12020145DOI Listing

Publication Analysis

Top Keywords

carbon aerogels
32
carbon
9
14-dioxane carbon
8
aerogels
8
heating rate
8
pyrolysis temperature
8
specific surface
8
surface area
8
adsorption capacity
8
adsorption
7

Similar Publications

We report the performance of solid-state ceramic supercapacitors (SSCs) based on a novel composite electrolyte comprising aluminum-doped lithium lanthanum titanate perovskite, LiLaTiAlO (Al-doped LLTO), and the ionic liquid 1-ethyl-3-methylimidazolium tetrafluoroborate (EMIM BF). Rietveld refinement of X-ray diffraction data confirms the preservation of the tetragonal perovskite phase after Al substitution, indicating structural stability of the host lattice. X-ray photoelectron spectroscopy (XPS) and Raman spectroscopy further corroborate the successful incorporation of Al without forming secondary phases.

View Article and Find Full Text PDF

Cellulose-based aerogels modulate fragrance adsorption and controlled release by carbonization/in-situ aromatization.

Carbohydr Polym

November 2025

Flavors and Fragrance Engineering & Technology Research Center of Henan Province, College of Tobacco Science, Henan Agricultural University, Zhengzhou 450000, China. Electronic address:

Fragrances are indispensable additives in consumer products including foods, cosmetics, and tobacco products. However, their inherent instability leads to rapid quality degradation and performance loss, driving the urgent need for controlled-release systems to stabilize fragrance performance. In this work, cellulose nanofibers (CNF) were used to prepare CNF aerogel-like gels (CA) and carbonized CNF aerogels (C-CA) through freeze-drying and high-temperature carbonization.

View Article and Find Full Text PDF

Aerogels are widely used in environmental remediation, but their application is hindered by brittleness, limited oil absorption and poor separation of viscous crude oil. In this study, a multifunctional superhydrophobic aerogel with electrothermal and photothermal effects was prepared from bacterial cellulose (BC), methyltrimethoxysilane (MTMS), and hydroxylated carbon nanotubes (HCNT) by soft-hard synergistic and directed freezing. The prepared aerogel exhibited an oriented layered porous structure with excellent compressibility and oil retention capacity.

View Article and Find Full Text PDF

Oriented synergistic assembly of one-dimensional Te nanowires/SWCNTs for high-performance thermoelectric aerogels.

J Colloid Interface Sci

August 2025

State Key Laboratory of Advanced Fiber Materials, College of Materials Science and Engineering, Donghua University, Shanghai 201620, PR China; School of Materials Science and Engineering, Shanghai Dianji University, Shanghai 201306, PR China. Electronic address:

The decoupling of thermoelectric performance parameters to coordinately optimize power factor (PF) and figure of merit (ZT) remains a critical challenge. Aerogels are valued for their low thermal conductivity and light weight; however, the lower electrical properties also lead to poor ZT values that affect their practical use. Herein, we implement a directional assembly strategy integrating Te nanowires (Te NWs) with single-walled carbon nanotubes (SWCNTs) to construct a three-dimensional interwoven network.

View Article and Find Full Text PDF

A review on controllable preparation and applications of biomass-based carbon aerogels.

Bioresour Technol

August 2025

State Key Laboratory of Coal Combustion, School of Energy and Power Engineering, Huazhong University of Science and Technology, Wuhan 430074, China.

Biomass-based carbon aerogels have emerged as sustainable porous carbon materials with ultralow density, high surface area, and tunable surface function groups. However, precise regulation toward different applications remains a significant challenge for maximum optimizing their performance. In this review, a comprehensive overview of the diverse methods for the controlled synthesis of biomass-based carbon aerogels from renewable feedstocks was provided, with emphasis on precursor selection, gelation chemistry, drying strategies, carbonization, and activation processes.

View Article and Find Full Text PDF