98%
921
2 minutes
20
Probiotics are live microorganisms that can have beneficial effects on humans. Encapsulation offers them a better chance of survival. Therefore, nozzle-free electrospinning was introduced for their embedding in nanofibrous material. Probiotic Lactobacillus paragasseri K7 in lyophilized and fresh form, with and without inulin as prebiotic, was added to a polymer solution of sodium alginate (NaAlg) and polyethylene oxide (PEO). Conductivity, viscosity, pH, and surface tension were determined to define the optimal concentration and volume ratio for smooth electrospinning. The success of the formed nanoscale materials was examined by scanning electron microscope (SEM), while the entrapment of probiotics in the nanofibrous mats was detected by attenuated total reflection-Fourier transform infrared spectroscopy (ATR-FTIR) and X-ray photoelectron spectroscopy (XPS). Spontaneous diffusion of bacteria from electrospun samples in PBS buffer pH 7.4 was studied by plate counting on MRS agar. By exposing polymer solutions containing L. paragasseri K7 and inulin to a high electric field, the nanofilm was formed on a polypropylene substrate, used as collecting material. When polymer solutions without inulin were used, the bead-like nanofibers may have become visible. The SEM results suggest that inulin, in addition to K7 strain, additionally lowers the conductivity of spinning macromolecular solution and hinders the nanofiber formation. The results of ATR-FTIR confirmed the presence of L. paragasseri K7 embedded in nanocomposites by the appearance of characteristic peaks. The samples containing the probiotic regardless of its form with inulin had similar surface composition, except that the sodium content was higher in the samples with fresh probiotic, probably due to greater and thus less easy embedding of the bacteria in NaAlg. Within 2 h, the largest amount of probiotic strain K7 was spontaneously released from the electrospun sample containing the inulin and probiotic in freeze-dried form (44%), while the amount released from the nanofibrous sample, which also contained the inulin and probiotic in fresh form, was significantly lower (21%). These preliminary results demonstrate the potential of nozzle-free electrospinning technology for the development of probiotic delivery systems for short-term use, such as feminine hygiene materials (tampons, pads, napkins).
Download full-text PDF |
Source |
---|---|
http://dx.doi.org/10.1007/s12010-023-04416-x | DOI Listing |
Appl Biochem Biotechnol
November 2023
Laboratory for Characterization and Processing of Polymers, Institute of Engineering Materials and Design, Faculty of Mechanical Engineering, University of Maribor, 2000, Maribor, Slovenia.
Probiotics are live microorganisms that can have beneficial effects on humans. Encapsulation offers them a better chance of survival. Therefore, nozzle-free electrospinning was introduced for their embedding in nanofibrous material.
View Article and Find Full Text PDFPharmaceutics
July 2022
Faculty of Pharmacy, Interdisciplinary Excellence Centre, Institute of Pharmaceutical Technology and Regulatory Affairs, University of Szeged, Eötvös Street 6, 6720 Szeged, Hungary.
The study aimed to prepare ciprofloxacin-loaded polyvinylpyrrolidone electrospun nanofibers for oral drug delivery, using a conventional nozzle-based and a lab-built nozzle-free electrospinning equipment. To produce nanofibers, electrospinning is the process most often used. However, from the industry's point of view, conventional electrospinning does not have sufficiently high productivity.
View Article and Find Full Text PDFMed Eng Phys
June 2021
School of Engineering, Institute for Materials and Processes, The University of Edinburgh, Robert Stevenson Road, Edinburgh, EH9 3FB, United Kingdom.. Electronic address:
This technical note provides a step-by-step guide for the design and construction of a temperature-controlled nozzle-free electrospinning device. The equipment uses a rotating mandrel partially immersed within a polymer solution to produce fibers in an upward motion by inducing the formation of multiple Taylor cones and subsequently multi-jetting out of an electrified open surface. Free-surface electrospinning can overcome limitations and drawbacks associated with single and multi-nozzle spinneret configurations, such as low yield, limited production capacity, nonuniform electric field distribution, and clogging.
View Article and Find Full Text PDFMater Sci Eng C Mater Biol Appl
July 2020
School of Engineering, Institute for Materials and Processes, The University of Edinburgh, King's Buildings, Edinburgh EH9 3FB, United Kingdom. Electronic address:
In this work, a nozzle-free electrospinning device was built to obtain high-throughput production of silk fibroin-based biocompatible composite fibers with tunable wettability. Synthetic biomaterials tend to present suboptimal cell growth and proliferation, with many studies linking this phenomenon to the hydrophobicity of such surfaces. In this study, electrospun mats consisting of Poly(caprolactone) blended with variant forms of Poly(glycerol sebacate) (PGS) and regenerated silk fibroin were fabricated.
View Article and Find Full Text PDFMed Eng Phys
September 2019
The School of Engineering, Institute for Materials and Processes, The University of Edinburgh, King's Buildings, Edinburgh EH9 3FB, United Kingdom. Electronic address:
A novel composite for skin tissue engineering applications by use of blends of Poly(vinylpyrrolidone) (PVP) and Poly (glycerol sebacate) (PGS) was fabricated via the scalable nozzle-free electrospinning technique. The formed PVP:PGS blends were morphologically, thermochemically and mechanically characterized. The morphology of the developed fibers correlated to the blend ratio.
View Article and Find Full Text PDF