Category Ranking

98%

Total Visits

921

Avg Visit Duration

2 minutes

Citations

20

Article Abstract

Objectives: To assess the potential trends for the year 2030 in dental implant dentistry in Europe using the Delphi methodology.

Material And Methods: A steering committee and a management team of experts in implant dentistry were created and validated a questionnaire including 60 questions, divided in eight topics. The survey was conducted in two rounds using an anonymous questionnaire, which provided the participants in the second round with the results of the first. Each question had three possible answers, and the results were expressed as percentages.

Results: A total of 138 experts were invited to participate in the survey. From all the invited experts, 52 answered in both the first and second rounds. Three different consensus categories were established based on the percentage of agreement: no consensus (<65%); moderate consensus (65%-85%); and high consensus (≥86%). Within the topic categories, a consensus was reached (mainly moderate consensus) for the majority of questions discussed among experts during a face to face consensus meeting. However, consensus was not reached for a small number of questions/topics.

Conclusions: About 82% of the questions reached consensus. The consensus points towards a lower number of implants to replace chewing units, with implants surfaces made of bioactive materials with reduced micro-roughness using mainly customized abutments with polished surfaces and an internal implant-abutment connection (85%). CBCT-3D technologies will be the main tool for pre-surgical implant placement diagnosis together with direct digital restorative workflows. There will be an increase in the incidence of peri-implantitis, although there will be more efficient interventions its treatment and prevention.

Download full-text PDF

Source
http://dx.doi.org/10.1111/clr.13431DOI Listing

Publication Analysis

Top Keywords

implant dentistry
12
dentistry europe
8
year 2030
8
european association
4
association osseointegration
4
osseointegration delphi
4
delphi study
4
study trends
4
trends implant
4
europe year
4

Similar Publications

Purpose: This study aimed to evaluate the inherent and after cyclic loading fracture strength of implant-supported cantilevered fixed prostheses fabricated from recently introduced additively manufactured (AM) and subtractively manufactured (SM) materials, considering variations in prosthesis height.

Materials And Methods: Three cylinder-shaped master files (20 mm long and 11 mm wide) with varying heights (7, 11, and 15 mm) and a titanium-base (Ti-base) abutment space were designed. These designs were used to fabricate a total of 144 specimens with two AM resins indicated for definitive use (Crowntec; AM-CT and Flexcera Smile Ultra+; AM-FS), one high-impact polymer composite (breCAM.

View Article and Find Full Text PDF

Enhancing the accuracy of full-arch digital implant impressions via segmentation: An in vitro study.

J Prosthodont

September 2025

Department of Graphic Design and Engineering Projects, Faculty of Engineering Gipuzkoa, University of the Basque Country UPV/EHU, San Sebastian, Spain.

Purpose: The aim of this in vitro study was to assess whether the accuracy (trueness and precision) of full-arch implant digital impressions can be improved by replacing standard digital impressions (StDIs) with segmented digital impressions (SgDIs), obtained by superimposing short-span digital impressions using a geometric pattern.

Materials And Methods: The study was conducted using a commercial edentulous maxillary model with four implants-positioned at the sites of the canines and second molars-and four commercial intraoral scan bodies (ISBs) screwed to them. Ten StDIs and SgDIs of the model were obtained, and their accuracy was evaluated and compared in terms of trueness and precision, based on measurements of three distances and three angles between the ISBs.

View Article and Find Full Text PDF

Purpose: To present a novel digital workflow (the Columbus Digital Bridge Protocol) for immediately loaded full-arch rehabilitations, integrating digital technologies throughout diagnostic, surgical and prosthetic phases, with a focus on the application of intraoral photogrammetry scanning.

Materials And Methods: The workflow presented in this article, successfully implemented in 14 patients, includes standardised clinical steps: digital diagnostic planning through matching of facial scans and CBCT data, surgical placement of four implants following tooth extraction, immediate post-surgical intraoral photogrammetry scanning using a three-step procedure (i.e.

View Article and Find Full Text PDF

Titanium is widely used for dental implant abutments due to its mechanical strength, biocompatibility, and corrosion resistance; however, its gray coloration can compromise esthetic outcomes, particularly in patients with thin or translucent gingival biotypes. Anodization, a surface modification technique altering the titanium oxide layer, has been proposed to improve soft tissue aesthetics by producing abutments with warmer tones (eg, pink or gold) that harmonize with the surrounding gingiva. This systematic review aimed to evaluate the clinical and aesthetic outcomes of anodized titanium abutments compared to non-anodized titanium and other materials, with a focus on peri-implant soft tissue health and visual integration.

View Article and Find Full Text PDF

Purpose: This study evaluated the fit of implant-supported bars fabricated using different computer-aided manufacturing (CAM) techniques.

Materials And Methods: A mandibular model with four dental implants (Nobel Replace Conical Connection, 3.5 mm × 11.

View Article and Find Full Text PDF