Category Ranking

98%

Total Visits

921

Avg Visit Duration

2 minutes

Citations

20

Article Abstract

Background: After amputation patients are more likely to injure their residual limb. An injury of a previously amputated limb, especially if the residuum is not anatomically normal, poses a dilemma for management. Case Description and Methods: This case report discusses a femoral fracture sustained proximal to a through-knee amputation. Findings and outcomes: The fracture was at the site of a malunited fracture. A shortening osteotomy with bone graft was undertaken to improve alignment and prosthetic fit and remove poor-quality bone. This was stabilised using an intramedullary nail, supplemented with an anti-rotation plate. This fracture went on to uneventful union, and the patient was able to comfortably use a prosthesis with increased functionality compared with prior to the recent injury.

Discussion: This management enabled quick healing of the fracture without the need to resort to a more proximal amputation.

Conclusion: In these unusual cases, careful planning is necessary to ensure all aspects of the problem is dealt with. Each case should be treated on its own merits. Clinical relevance This case demonstrates the difficulty in care of complex limb trauma and offers a solution for management of similar cases. Excellent results are possible when all surgical options are considered.

Download full-text PDF

Source
http://dx.doi.org/10.1177/0309364616683821DOI Listing

Publication Analysis

Top Keywords

malunited fracture
8
fracture
6
successful management
4
management femoral
4
femoral trauma
4
trauma through-knee
4
through-knee amputee
4
amputee previous
4
previous malunited
4
fracture implications
4

Similar Publications

Introduction: This case report describes the utilization of patient-specific 3D modeling for the care of a 13-year-old patient with a distal radius malunion and partial growth arrest.

Methods: Patient-specific 3D models of the patient's wrist were created using computed tomography scans. Digital modeling software was used to determine the appropriate orientation of the osteotomy, size and shape of bone graft, and final wrist alignment.

View Article and Find Full Text PDF

Bony Mallet Finger Malunion: Corrective Osteotomy Technique.

Tech Hand Up Extrem Surg

September 2025

Department of Hand and Upper Extremity, Hospital for Special Surgery, New York, NY.

Although many mallet finger injuries are effectively managed with nonoperative treatment, failure to address these bony mallet fingers can lead to complications such as soft tissue imbalances or a bony mallet malunion, ultimately resulting in a chronic mallet injury. As these chronic injuries progress, patients often report considerable functional impairment, pain, and stiffness. Various surgical techniques have been described to treat chronic mallet injuries, but many of them fail to restore DIP extension, particularly in severe cases when patients have bony malunions or hyperlaxity.

View Article and Find Full Text PDF

Corrective osteotomy for a malunited distal radial fracture (DRF) can be challenging. Three-dimensional printing techniques can be used to produce patient specific implants (PSIs). Theoretically, this technique improves accuracy of reconstruction and therefore patient-related outcomes.

View Article and Find Full Text PDF

The burden, management and treatment outcomes of gunshot-induced fractures of the forearm at a tertiary hospital in South Africa.

J Orthop Trauma

July 2025

Division of Orthopaedic Surgery, Department of Surgical Sciences, Faculty of Medicine and Health Sciences, Stellenbosch University, Cape Town, 7505, South Africa.

Objectives: To assess the burden, management and outcomes of gunshot-induced extra-articular forearm fractures at a tertiary institution in the Western Cape of South Africa.

Methods: Design: Retrospective review.

Setting: Single centre, Level 1 trauma centre.

View Article and Find Full Text PDF

ObjectivesTo report on the process and results of clinical application of 3D printed patient-specific metal plates in orthopaedic trauma.Materials and MethodsA retrospective review was conducted on 11 pilot patients managed with 3D printed Patient-Specific Plates (PSPs) together with 3D printed guides, 3D printed bone models and 3D virtual planning for malunions or acute fractures. There were six clavicles, three forearm shafts, one ankle, and one tibial plateau.

View Article and Find Full Text PDF