Controlling the physicochemical state of carbon on graphene using focused electron-beam-induced deposition.

ACS Nano

George W. Woodruff School of Mechanical Engineering, ‡School of Materials Science and Engineering, and §Parker H. Petit Institute for Bioengineering and Bioscience, Georgia Institute of Technology, Atlanta, Georgia 30332, United States.

Published: July 2014


Category Ranking

98%

Total Visits

921

Avg Visit Duration

2 minutes

Citations

20

Article Abstract

Focused electron-beam-induced deposition (FEBID) is a promising nanolithography technique using "direct-write" patterning by carbon line and dot deposits on graphene. Understanding interactions between deposited carbon molecules and graphene enables highly localized modification of graphene properties, which is foundational to the FEBID utility as a nanopatterning tool. In this study, we demonstrate a unique possibility to induce dramatically different adsorption states of FEBID-produced carbon deposits on graphene, through density functional theory calculations and complementary Raman experiments. Specifically, an amorphous carbon deposit formed by direct irradiation of high energy primary electrons exhibits unusually strong interactions with graphene via covalent bonding, whereas the FEBID carbon formed due to low-energy secondary electrons is only weakly interacting with graphene via physisorption. These observations not only are of fundamental importance to basic physical chemistry of FEBID carbon-graphene interactions but also enable the use of selective laser-assisted postdeposition ablation to effectively remove the parasitically deposited, physisorbed carbon films for improving FEBID patterning resolution.

Download full-text PDF

Source
http://dx.doi.org/10.1021/nn5011073DOI Listing

Publication Analysis

Top Keywords

focused electron-beam-induced
8
electron-beam-induced deposition
8
deposits graphene
8
carbon
7
graphene
7
febid
5
controlling physicochemical
4
physicochemical state
4
state carbon
4
carbon graphene
4

Similar Publications

Electron beam-induced damage in tellurium dioxide.

Micron

November 2025

OIST Graduate University, 1919-1 Tancha, Onna, 904-0495, Okinawa, Japan. Electronic address:

In this work, structural and compositional changes in α-TeO, also known as paratellurite, were studied as function of 300 kV electron beam exposure. Firstly, the mean free path for electron scattering in α-TeO was measured, to enable local specimen thickness measurement and estimation of scattering probabilities. A value of λ = 155 nm ± 6 nm was obtained, for the specific experimental conditions as detailed in the text.

View Article and Find Full Text PDF

Liquid-cell annular dark-field scanning transmission electron microscopy imaging of single crystal samples on a low-index zone-axis incidence condition.

Micron

November 2025

Research Center for Energy and Environmental Materials, National Institute for Materials Science, Tsukuba, Ibaraki, Japan; Graduate School of Science and Technology, University of Tsukuba, Tsukuba, Ibaraki, Japan.

In liquid cell (LC) annular dark-field scanning transmission electron microscopy (ADF-STEM), the spatial resolution is limited by the low ratio of signals from samples to background signals from the silicon nitride window membranes and liquid. We report the development of a double-tilt LC holder for atomic-resolution LC-ADF-STEM imaging of single-crystal samples under zone-axis incidence conditions. A SrTiO <001> lamellar sample, approximately 100 nm thick, was prepared using the focused ion beam technique and transferred onto a silicon nitride window membrane of an LC chip via a glass probe pick-up method in air, which avoids Ga ion beam-induced damage to the window membrane.

View Article and Find Full Text PDF

In this study, we present a protocol to visualise, track and distinguish between two different binder components commonly used for batteries, styrene butadiene rubber (SBR) and sodium carboxymethyl cellulose (CMC), within a composite hard carbon electrode for sodium-ion batteries using a two-step staining method. The application of osmium tetroxide (OsO) vapour followed by uranyl acetate (UA) solution enables the staining of different functional groups and the individual tracing of SBR and CMC by energy dispersive X-ray spectroscopy (EDX) measurements using the osmium (Os) and uranium (U) content. This staining procedure and the filling of the pore space with conductive platinum carbon (PtC) composite via local electron-beam-induced deposition (EBID) results in an excellent contrast for all components of the electrode material.

View Article and Find Full Text PDF

Electron beam induced effects in liquid phase transmission electron microscopy (LPTEM) encompass changes introduced to both the liquid sample and the material encapsulating the liquid. Typically, LPTEM beam effect studies have focused on the interaction of the electron beam with the liquid itself, while the interaction with the encapsulating material has often not been considered. Here, the chemical changes of silicon nitride (SiN) thin films exposed to water, which are the conditions typically used in commercial LPTEM systems have been studied.

View Article and Find Full Text PDF

Measurement of electron beam induced sample heating in SEM experiments.

Ultramicroscopy

October 2025

National Centre for Nano Fabrication and Characterization (DTU Nanolab), Technical University of Denmark (DTU), Kgs Lyngby, Denmark. Electronic address:

Scanning Electron Microscopy (SEM) experiments provide detailed insights into material microstructures, enabling high-resolution imaging as well as crystallographic analysis through advanced techniques like Electron Backscatter Diffraction (EBSD). However, the interaction of the high-energy electron beam with the material can lead to localized heating, which may significantly impact specimen integrity, especially in applications requiring prolonged beam exposure, for instance when mapping the crystal structure using EBSD. This study examines electron-beam-induced heating effects on a model metal sample (iron), directly measuring the locally deposited electron beam energy with a MEMS-based heating device and validating these measurements through simulations, including Monte Carlo and Finite Element methods.

View Article and Find Full Text PDF