Theoretical Prediction of Electrical Conductivity Percolation of Poly(lactic acid)-Carbon Nanotube Composites in DC and RF Regime.

Polymer composites based on polylactic acid (PLA) reinforced with 0.25-5 wt.% of carbon nanotubes (CNTs) were synthesized by melt blending.

Absorption Performances of PLA-Montmorillonite Nanocomposites Thin Films in Salisbury and Rozanov Configurations: Influence of Aging and Mechanical Recycling.

The present paper aims to address the crucial concern of pollution induced by growing plastic waste and electromagnetic interference (EMI). Nanocomposites combining poly(lactic acid) (PLA) and organo-modified montmorillonite (OMMT) are synthesized and compression molded into thin films. A first set of samples, referred as virgin, was kept as is, while a second set of samples were photochemically, thermally and hydrolytically aged before mechanical recycling via extruding and second compression molding, resulting in the so-called recycled composite.

Electromagnetic performance, optical and physiochemical features of CaTiO/NiO and SrFeO/NiO nanocomposites based bilayer absorber.

Herein, two distinct nanocomposites of CaTiO micro-cubes and polygonal SrFeO, both decorated with NiO nanoparticles, were successfully synthesized using hydrothermal method. The physico-chemical features of as-prepared samples were evaluated via XRD, FTIR, UV-vis, BET, XPS, FESEM and EDS analysis. Microwave attenuation features of as-prepared single layer absorbers were determined by VNA analysis in 2-18 GHz.

Optimum power transfer in RF front end systems using adaptive impedance matching technique.

Matching the antenna's impedance to the RF-front-end of a wireless communications system is challenging as the impedance varies with its surround environment. Autonomously matching the antenna to the RF-front-end is therefore essential to optimize power transfer and thereby maintain the antenna's radiation efficiency. This paper presents a theoretical technique for automatically tuning an LC impedance matching network that compensates antenna mismatch presented to the RF-front-end.

High-isolation antenna array using SIW and realized with a graphene layer for sub-terahertz wireless applications.

This paper presents the results of a study on developing an effective technique to increase the performance characteristics of antenna arrays for sub-THz integrated circuit applications. This is essential to compensate the limited power available from sub-THz sources. Although conventional array structures can provide a solution to enhance the radiation-gain performance however in the case of small-sized array structures the radiation properties can be adversely affected by mutual coupling that exists between the radiating elements.

Bandwidth and gain enhancement of composite right left handed metamaterial transmission line planar antenna employing a non foster impedance matching circuit board.

The paper demonstrates an effective technique to significantly enhance the bandwidth and radiation gain of an otherwise narrowband composite right/left-handed transmission-line (CRLH-TL) antenna using a non-Foster impedance matching circuit (NF-IMC) without affecting the antenna's stability. This is achieved by using the negative reactance of the NF-IMC to counteract the input capacitance of the antenna. Series capacitance of the CRLH-TL unit-cell is created by etching a dielectric spiral slot inside a rectangular microstrip patch that is grounded through a spiraled microstrip inductance.

Predictive Optimization of Electrical Conductivity of Polycarbonate Composites at Different Concentrations of Carbon Nanotubes: A Valorization of Conductive Nanocomposite Theoretical Models.

Polycarbonate-carbon nanotube (PC-CNT) conductive composites containing CNT concentration covering 0.25-4.5 wt.

Power balance and efficiency of metasurface antennas.

This paper presents two methods for the efficient evaluation of the power balance in circular metasurface (MTS) antennas implementing arbitrary modulated surface impedances on a grounded dielectric slab. Both methods assume the surface current in the homogenized MTS to be known. The first technique relies on the surface current expansion with Fourier-Bessel basis functions (FBBF) and proceeds by integration of the Poynting vector on a closed surface.

Investigation of Microwave Absorption Performance of CoFeO/NiFeO/Carbon Fiber Composite Coated with Polypyrrole in X-Band Frequency.

The current research reports the preparation of a microwave absorber containing CoFeO/NiFeO/Carbon fiber (H/S/CF) coated with polypyrrole polymer (PPy@H/S/CF) through sol-gel and in-situ polymerization processes. X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), vibrating sample magnetometer (VSM), and a vector network analyzer (VNA) are utilized to evaluate the features of the prepared composite. The microstructure analysis results revealed carbon fibers well decorated with submicron-size particles having hard/soft magnetic phases and thoroughly coated with polymer.

Simulation and Optimization of Electromagnetic Absorption of Polycarbonate/CNT Composites Using Machine Learning.

Electronic devices that transmit, distribute, or utilize electrical energy create electromagnetic interference (EMI) that can lead to malfunctioning and degradation of electronic devices. EMI shielding materials block the unwanted electromagnetic waves from reaching the target material. EMI issues can be solved by using a new family of building blocks constituted of polymer and nanofillers.

Editorial for the Special Issue on "Nanodevices for Microwave and Millimeter Wave Applications".

Initially inspired by the work of Richard Feynman in 1959 during his famous talk "There is plenty of room at the bottom", nanoscience and nanotechnology have moved during the 2000s from laboratory developments to daily life applications [...

Highly Efficient Wideband Microwave Absorbers Based on Zero-Valent Fe@-FeO and Fe/Co/Ni Carbon-Protected Alloy Nanoparticles Supported on Reduced Graphene Oxide.

Electronic systems and telecommunication devices based on low-power microwaves, ranging from 2 to 40 GHz, have massively developed in the last decades. Their extensive use has contributed to the emergence of diverse electromagnetic interference (EMI) phenomena. Consequently, EMI shielding has become a ubiquitous necessity and, in certain countries, a legal requirement.

Fabrication of Microwave Devices Based on Magnetic Nanowires Using a Laser-Assisted Process.

This paper compares two laser-assisted processes developed by the authors for the fabrication of microwave devices based on nanowire arrays loaded inside porous alumina templates. Pros and cons of each process are discussed in terms of accuracy, reproducibility and ease of fabrication. A comparison with lithography technique is also provided.

A laser-assisted process to produce patterned growth of vertically aligned nanowire arrays for monolithic microwave integrated devices.

An experimental process for the fabrication of microwave devices made of nanowire arrays embedded in a dielectric template is presented. A pulse laser process is used to produce a patterned surface mask on alumina templates, defining precisely the wire growing areas during electroplating. This technique makes it possible to finely position multiple nanowire arrays in the template, as well as produce large areas and complex structures, combining transmission line sections with various nanowire heights.

Colloidal pattern replication through contact photolithography operated in a 'Talbot-Fabry-Perot' regime.

We describe a method for continuous colloidal pattern replication using contact photolithography. Cr-on-quartz masks are fabricated using colloidal nanosphere lithography and subsequently used as photolithography stamps. Hexagonal pattern arrangements with different dimensions (980, 620 and 480 nm, using colloidal particles with these respective diameters) have been studied.

Wavelength-scale lens microscopy via thermal reshaping of colloidal particles.

Lenses are by far the most simple tools for visualization. Although they are intrinsically limited in resolution, recent efforts have aimed at focusing visible light in micro-scale lenses with subwavelength resolution, triggering an intense interest in further improving and understanding their performances. Herein, we report on a distinctive library of wavelength-scale solid immersion lenses facilitated the self-assembly of polystyrene colloidal particles.

Functionalized nanoporous thin films from photocleavable block copolymers.

A polystyrene-block-poly(ethylene oxide) block copolymer bearing a photocleavable junction between the blocks is used to form nanoporous thin films with carboxylic acid functions homogeneously distributed on the pore walls. The presence of the carboxylic acid groups is evidenced by fluorescence spectroscopy after their reaction with a diazomethane functionalized fluorescent dye. In addition, the initial light-responsive thin film, acting as a photoresist, can be easily patterned to selectively generate porosity in predetermined areas.

Straightforward synthesis of conductive graphene/polymer nanocomposites from graphite oxide.

The reduction of graphite oxide (GO) in the presence of reactive poly(methyl methacrylate) (PMMA), under mild biphasic conditions, directly affords graphene grafted with PMMA. The resulting nanocomposite shows excellent electrical conductivities resulting from the optimal dispersion and exfoliation of graphene in the polymer matrix.

Locating carbon nanotubes (CNTs) at the surface of polymer microspheres using poly(vinyl alcohol) grafted CNTs as dispersion co-stabilizers.

In this communication, we prepared carbon nanotubes (CNTs) modified by poly(vinyl alcohol) that are used as co-stabilizers for the dispersion polymerization of methyl methacrylate. Poly(methyl methacrylate) microspheres with CNTs selectively located at their surface are formed. This specific localization is a way to enhance the electrical conductivity of the nanocomposite.